An investigation of the mechanical properties and wear resistance of NiCrBSi coatings carried out by in situ laser remelting

[1]  J. Nohava,et al.  Interesting aspects of indentation and scratch methods for characterization of thermally-sprayed coatings , 2010 .

[2]  N. Serres,et al.  Dry coatings and ecodesign part. 1 — Environmental performances and chemical properties , 2009 .

[3]  G. Bolelli.  Replacement of hard chromium plating by thermal spraying – problems, solutions and possible future approaches , 2009 .

[4]  Jesús Rodríguez,et al.  Influence of the deposition techniques on the mechanical properties and microstructure of NiCrBSi coatings , 2008 .

[5]  S. Guessasma,et al.  Friction moment prediction of HVOF coatings and Electroplated Hard Chromium , 2008 .

[6]  R. Vijande,et al.  Parallel laser melted tracks: Effects on the wear behaviour of plasma-sprayed Ni-based coatings , 2008 .

[7]  J. Guilemany,et al.  Cr3C2–NiCr and WC–Ni thermal spray coatings as alternatives to hard chromium for erosion–corrosion resistance , 2008 .

[8]  I. Peñuelas,et al.  Microstructural study of NiCrBSi coatings obtained by different processes , 2007 .

[9]  V. Cannillo,et al.  Wear behaviour of thermally sprayed ceramic oxide coatings , 2006 .

[10]  H. Pokhmurska,et al.  Comparison of hardmetal and hard chromium coatings under different tribological conditions , 2006 .

[11]  M. Staia,et al.  Interfacial indentation and shear tests to determine the adhesion of thermal spray coatings , 2006 .

[12]  V. Cannillo,et al.  Mechanical and tribological properties of electrolytic hard chrome and HVOF-sprayed coatings , 2006 .

[13]  H. Liao,et al.  Relationships between NiCrBSi particle characteristics and corresponding coating properties using different thermal spraying processes , 2005 .

[14]  C. Berndt,et al.  Fatigue and Deformations of HVOF Sprayed WC-Co Coatings vs. Hard Chrome Plating , 2003, Thermal Spray 2003: Proceedings from the International Thermal Spray Conference.

[15]  E. Souza,et al.  Correlation between residual stresses and adhesion of plasma sprayed coatings: effects of a post-annealing treatment , 2002 .

[16]  Wilfried Kurz,et al.  Columnar to equiaxed transition in solidification processing , 2001 .

[17]  D. Stöver,et al.  Changes in porosity and Young’s Modulus due to sintering of plasma sprayed thermal barrier coatings , 1999 .

[18]  L. Pawlowski,et al.  Thick laser coatings: A review , 1999 .

[19]  Hyungjun Kim,et al.  Elastic modulus of plasma-sprayed coatings determined by indentation and bend tests , 1999 .

[20]  T. Quinn.  Computational methods applied to oxidational wear , 1996 .

[21]  D. Chicot,et al.  Apparent interface toughness of substrate and coating couples from indentation tests , 1996 .

[22]  G. Pharr,et al.  An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments , 1992 .

[23]  G. Zambelli,et al.  Measurement of cohesion and adhesion strengths in alumina coatings produced by plasma spraying , 1989 .

[24]  J. Archard.  Contact and Rubbing of Flat Surfaces , 1953 .

[25]  G. Montavon,et al.  Microstructures of partially stabilized zirconia manufactured via hybrid plasma spray process , 2005 .