The Influence of Joint Inclination and Opening Width on Fracture Characteristics of Granite under Triaxial Compression

[1]  Chong Shi,et al.  Application of Discrete-Element Numerical Simulation for Calculating the Stability of Dangerous Rock Mass: A Case Study , 2020 .

[2]  Y. Shou,et al.  Understanding the fracture mechanism of ring Brazilian disc specimens by the phase field method , 2020, International Journal of Fracture.

[3]  Abhay Kumar Mandal,et al.  Analysis of energy dissipation and crack evolution law of sandstone under impact load , 2020 .

[4]  Investigation of mechanical properties of jointed granite under compression using lattice-spring-based synthetic rock mass modeling approach , 2020 .

[5]  Chong Shi,et al.  Calibration of micro-scaled mechanical parameters of granite based on a bonded-particle model with 2D particle flow code , 2019, Granular Matter.

[6]  Yujing Jiang,et al.  Mechanism of shear deformation, failure and energy dissipation of artificial rock joint in terms of physical and numerical consideration , 2018, Geosciences Journal.

[7]  Ping Cao,et al.  An Experimental and Numerical Study on Mechanical Behavior of Ubiquitous-Joint Brittle Rock-Like Specimens Under Uniaxial Compression , 2016, Rock Mechanics and Rock Engineering.

[8]  Gang Wang,et al.  Rate-dependent mechanical behavior of rough rock joints , 2016 .

[9]  Louis Ngai Yuen Wong,et al.  Choosing a proper loading rate for bonded-particle model of intact rock , 2014, International Journal of Fracture.

[10]  Catherine O'Sullivan,et al.  Discrete element method simulations of analogue reservoir sandstones , 2013 .

[11]  Huang Runqiu.  Influence of medium strain rate on sandstone with a single pre-crack under uniaxial compression using PFC simulation , 2013 .

[12]  Wang Yundong.  Simulation of Triaxial Tests of Marble Samples through the Particle Flow Code , 2012 .

[13]  Giovanni Battista Barla,et al.  A Bonded Particle Model Simulation of Shear Strength and Asperity Degradation for Rough Rock Fractures , 2012, Rock Mechanics and Rock Engineering.

[14]  Jia Shan-po.  TRIAXIAL TEST RESEARCH AND MECHANICAL ANALYSIS BASED ON STRUCTURE SURFACE EFFECT OF DEEP ROCK MASS WITH SINGLE FISSURE , 2012 .

[15]  Sheng-Qi Yang,et al.  Strength failure and crack coalescence behavior of brittle sandstone samples containing a single fissure under uniaxial compression , 2011 .

[16]  Seokwon Jeon,et al.  An experimental and numerical study of fracture coalescence in pre-cracked specimens under uniaxial compression , 2011 .

[17]  Jae-Joon Song,et al.  Numerical simulation of a direct shear test on a rock joint using a bonded-particle model , 2009 .

[18]  Sheng-Qi Yang,et al.  Experimental Investigation on Strength and Failure Behavior of Pre-cracked Marble Under Conventional Triaxial Compression , 2008 .

[19]  Jeoung Seok Yoon,et al.  Application of experimental design and optimization to PFC model calibration in uniaxial compression simulation , 2007 .

[20]  Liangming Liu,et al.  Particle simulation of spontaneous crack generation problems in large‐scale quasi‐static systems , 2007 .

[21]  Idar Larsen,et al.  Comparison between controlled laboratory experiments and discrete particle simulations of the mechanical behaviour of rock , 2005 .

[22]  Zhou Hongwei,et al.  ON ENERGY ANALYSIS OF ROCK FAILURE , 2005 .

[23]  P. Cundall,et al.  A bonded-particle model for rock , 2004 .

[24]  John A. Hudson,et al.  Draft ISRM suggested method for the complete stress-strain curve for intact rock in uniaxial compression , 1999 .