Monitoring and Analysis of a High-Performance Concrete Shaft Lining: A Case Study

Shaft lining in ultradeep mines on the coast of eastern China under the complex external environments of “high in situ stress and high osmotic pressure” has the disadvantages of failure; to solve this problem, the field test of high-performance concrete shaft lining structure was carried out in Sha-ling gold mine. The field test study of the high-performance concrete shaft lining was carried out in a −1120 m ingate and a −1114 m to −1124 m shaft. Its stress and deformation were monitored and analyzed. The maximum compressive stress of the HPC shaft lining structure at the level of −1117.7 m of the air intake shaft is 1.91 MPa. Based on the Von-Mises yield theory and the analytical solution of thick-walled cylinder theory, the ultimate limit of the high-performance concrete shaft lining in the Sha-ling gold mine was obtained. The high-performance concrete shaft lining strain changes smoothly, and concrete strain can be divided into three stages: the rapid growth period, the slow growth period, and the stable period. The monitoring results show that the high-performance concrete shaft lining has excellent mechanical properties in the external environment of high in situ stress, which can be used as a reference for the support design of similar projects.

[1]  X. Heping,et al.  Discing behavior and mechanism of cores extracted from Songke-2 well at depths below 4,500 m , 2022, International Journal of Rock Mechanics and Mining Sciences.

[2]  Zhi Dou,et al.  Influence of Shear Displacement on Fluid Flow and Solute Transport in a 3D Rough Fracture , 2021, Lithosphere.

[3]  Q. Yin,et al.  Numerical investigation on the fatigue failure characteristics of water-bearing sandstone under cyclic loading , 2021, Journal of Mountain Science.

[4]  Zhi Dou,et al.  Influence of Layer Transition Zone on Rainfall-Induced Instability of Multilayered Slope , 2021, Lithosphere.

[5]  Gan Li,et al.  Analysis of deformation control mechanism of prestressed anchor on jointed soft rock in large cross-section tunnel , 2021, Bulletin of Engineering Geology and the Environment.

[6]  Donghui Chen,et al.  An analytical solution of equivalent elastic modulus considering confining stress and its variables sensitivity analysis for fractured rock masses , 2021, Journal of Rock Mechanics and Geotechnical Engineering.

[7]  Chen Cao,et al.  Quantitative estimation of debris flow source materials by integrating multi-source data: A case study , 2021 .

[8]  Heping Xie,et al.  Mechanical behavior of coal under different mining rates: A case study from laboratory experiments to field testing , 2021, International Journal of Mining Science and Technology.

[9]  Guangcheng Zhang,et al.  Flexural Toppling Mechanism and Stability Analysis of an Anti-dip Rock Slope , 2021, Rock Mechanics and Rock Engineering.

[10]  H. Ji,et al.  Performance change of shaft lining concrete under simulated coastal ultra-deep mine environments , 2020 .

[11]  Xiaoguang Jin,et al.  Long-term behaviors of concrete under low-concentration sulfate attack subjected to natural variation of environmental climate conditions , 2019, Cement and Concrete Research.

[12]  Zhigang Tao,et al.  Design and Application of a Monitoring System for a Deep Railway Foundation Pit Project , 2019, IEEE Access.

[13]  Weiming Wang,et al.  Deformation Monitoring and Stability Analysis of Shaft Lining in Weakly Cemented Stratum , 2018, Advances in Civil Engineering.

[14]  Guangsi Zhao,et al.  The Unified Strength Theory for Plastic Limit Load Analysis of Vertical Shaft Lining , 2018 .

[15]  M. F. Najjar,et al.  Damage mechanisms of two-stage concrete exposed to chemical and physical sulfate attack , 2017 .

[16]  A. Soliman,et al.  Investigation of concrete exposed to dual sulfate attack , 2014 .

[17]  Nele De Belie,et al.  Investigation of the influence of blast-furnace slag on the resistance of concrete against organic acid or sulphate attack by means of accelerated degradation tests , 2012 .

[18]  C. Oguchi,et al.  Resistance of plain and blended cement mortars exposed to severe sulfate attacks , 2011 .

[19]  Roman Loser,et al.  Analysis of concrete in a vertical ventilation shaft exposed to sulfate-containing groundwater for 45 years , 2011 .

[20]  Yang Zhi-jiang.  Horizontal Ultimate Bearing Capacity of Encased Steel Concrete Shaft Lining , 2011 .

[21]  Ma Xiumin,et al.  RESEARCH ON STRESS FIELD AND HYDRAULIC FRACTURING IN-SITU STRESS MEASUREMENT OF 1000 M DEEP HOLE IN ZHAOLOU COAL MINE , 2011 .

[22]  Ma Chengxuan,et al.  MODEL TEST RESEARCH ON SHAFT LINING BUILT IN HIGH PRESSURE ROCK AQUIFER , 2011 .

[23]  Rong Chuan-xin.  Research on vertical bearing capacity of shaft lining structure of high strength concrete and double steel cylinders in super-thick alluvium , 2010 .

[24]  Yao Zhi-shu.  RESEARCH ON MECHANICAL CHARACTERISTICS OF HIGH-STRENGTH REINFORCED CONCRETE SHAFT LINING IN DEEP ALLUVIUM , 2008 .

[25]  Rong Chuan-xin.  EXPERIMENTAL STUDY ON SHIFT-BORING LINING OF HIGH PERFORMANCE CONCRETE AND DOUBLE STEEL CYLINDER IN SUPER-DEEP ALLUVIUM , 2007 .

[26]  Lao Jun.  Study on the mechanical properties and constitutive relation of steel fiber reinforced concrete , 2007 .

[27]  Yao Zhi-shu.  AN EXPERIMENTAL STUDY ON STEEL FIBER REINFORCED HIGH STRENGTH CONCRETE SHAFT LINING IN DEEP ALLUVIUM , 2005 .

[28]  Jia Yao-dong,et al.  STUDY ON ROCK MECHANICS IN DEEP MINING ENGINEERING , 2005 .

[29]  L. Ya-ping.  Study on Modulus of Elasticity and Poisson Ratio of High Performance Concrete , 2004 .