Genetic Algorithm Optimization for Primary Surfaces Recuperator of Microturbine

In recent years, the genetic algorithm (GA) technique has gotten much attention in solving real-world problems. This technique has a strong ability for global searching and optimization based on various objectives for their optimal parameters. The technique may be applied to complicated heat exchangers and is particularly useful for new types. It is important to optimize the heat exchanger, for minimum volume/weight, to save fabrication cost or for improved effectiveness to save energy consumption, under the requirement of allowable pressure drop; simultaneously it is mandatory to optimize geometry parameters of heating plate from technical and economic standpoints. In this paper, GA is used to optimize the cross wavy primary surface (CWPS) and cross corrugated primary surface (CCPS) geometry characteristic of recuperator in a 100 kW microturbine, in order to get more compactness and minimum volume and weight. Two kinds of fitness assignment methods are considered. Furthermore, GA parameters are set optimally to yield smoother and faster fitness convergence. The comparison shows the superiority of GA and confirms its potential to solve the objective problem. When the rectangular recuperator core size and corrugated geometries are evaluated, in the CWPS the weight of the recuperator decreases by 12% or more; the coefficient of compactness increases by up to 19%, with an increase of total pressure drop by 0.84% compared to the original design data; and the total pressure drop versus the operating pressure is controlled to be less than 3%. In the CCPS area compactness is increased to 70% of the initial data by decreasing pitch and relatively high height of the passage, the weight decreases by 17-36%, depending on the inclination angle (θ). Comparatively the CCPS shows superior performance for use in compact recuperators in the future. The GA technique chooses from a variety of geometry characters, optimizes them and picks out the one which provides the closest fit to the recuperator for microturbine.

[1]  T. Newell,et al.  An experimental study of flow and heat transfer in sinusoidal wavy passages , 1999 .

[2]  Colin F. McDonald.  Low-cost compact primary surface recuperator concept for microturbines , 2000 .

[3]  M. Ciofalo,et al.  Investigation of flow and heat transfer in corrugated-undulated plate heat exchangers , 2000 .

[4]  Bengt Sundén,et al.  Evaluation of the Cross Corrugated and Some Other Candidate Heat Transfer Surfaces for Microturbine Recuperators , 2002 .

[5]  N. K. Mitra,et al.  Numerical Investigation of Convective Heat Transfer and Pressure Drop in Wavy Ducts , 2000 .

[6]  Laiqin Luo,et al.  Experimental Investigation on Heat Transfer and Pressure Drop in a Microtubine Recuperator With Cross-Wavy Primary Surface Channels , 2005 .

[7]  Bengt Sundén,et al.  A Comparison of Some Heat Transfer Surfaces for Small Gas Turbine Recuperators , 2001 .

[8]  Esa Utriainen.  Investigation of Some Heat Transfer Surfaces for Gas Turbine Recuperators , 2001 .

[9]  Ryoichi S. Amano,et al.  A Numerical Study of Laminar and Turbulent Heat Transfer in a Periodically Corrugated Wall Channel , 1985 .

[10]  Bengt Sundén,et al.  A numerical investigation of primary surface rounded cross wavy ducts , 2002 .

[11]  R Poulter,et al.  Hydrodynamics and thermal characteristics of corrugated channels: computational approach , 2000 .

[12]  Mitsuo Gen,et al.  Genetic algorithms and engineering optimization , 1999 .

[13]  M. Collins,et al.  Investigation of flow and heat transfer in corrugated passages—II. Numerical simulations , 1996 .

[14]  Qiuwang Wang,et al.  Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators , 2005 .

[15]  Alberto Traverso,et al.  Optimal design of compact recuperators for microturbine application , 2005 .

[16]  Nimai Kumar Mitra,et al.  NUMERICAL INVESTIGATION OF FLOW FIELD AND HEAT TRANSFER IN CROSS-CORRUGATED DUCTS , 1999 .