Influence of site, storage and steaming on Eucalyptus nitens log-end splitting

Key messageLog-end splitting is one of the single most important defects in veneer logs. We show that log-end splitting in the temperate plantation speciesEucalyptus nitensvaries across sites and within-tree log position and increases with time in storage.ContextLog-end splitting is one of the single most important defects in veneer logs because it can substantially reduce the recovery of veneer sheets. Eucalyptus nitens can develop log-end splits, but factors affecting log-end splitting in this species are not well understood.AimsThe present study aims to describe the effect of log storage and steaming on the development of log-end splitting in logs from different plantations and log positions within the tree.MethodsThe study was conducted on upper and lower logs from each of 41 trees from three 20–22-year-old Tasmanian E. nitens plantations. Log-end splitting was assessed immediately after felling, after transport and storage in a log-yard, and just before peeling. A pre-peeling steam treatment was applied to half the logs.ResultsSite had a significant effect on splitting, and upper logs split more than lower logs with storage. Splitting increased with tree diameter breast height (DBH), but this relationship varied with site. The most rapidly growing site had more splitting even after accounting for DBH. No significant effect of steaming was detected.ConclusionLog-end splitting varied across sites and within-tree log position and increased with time in storage.

[1]  B. Potts,et al.  Review of Eucalyptus nitens genetic parameters , 2008 .

[2]  H. Kubler.  Silvicultural control of mechanical stresses in trees , 1988 .

[3]  G. Turner.  The three astrolabes of Gerard Mercator , 1994 .

[4]  R. Marchal,et al.  The effect of log heating temperature on the peeling process and veneer quality: beech, birch, and spruce case studies , 2013, European Journal of Wood and Wood Products.

[5]  Carlos Alberto Oliveira de Matos,et al.  Lumber quality of Eucalyptus grandis as a function of diametrical position and log steaming. , 2010, Bioresource technology.

[6]  Professor Dr. Claus Mattheck,et al.  Wood - The Internal Optimization of Trees , 1995, Springer Series in Wood Science.

[7]  R. Shmulsky.  Effect of log storage on structural veneer processing , 2002 .

[8]  Shakti Chauhan,et al.  Wood quality: multifaceted opportunities , 2006 .

[9]  B. Potts,et al.  Achievements in forest tree improvement in Australia and New Zealand 9. Genetic improvement of Eucalyptus nitens in Australia , 2008 .

[10]  B. Potts,et al.  Meta-analysis of racial variation in Eucalyptus nitens and E. denticulata , 2011 .

[11]  Henri Baillères,et al.  Veneer Recovery Analysis of Plantation Eucalypt Species Using Spindleless Lathe Technology , 2013 .

[12]  M. Bariska.  Collapse phenomena in eucalypts , 1992, Wood Science and Technology.

[13]  J. Gril,et al.  Modelling Log-End Cracks Due to Growth Stresses: Calculation of the Elastic Energy Release Rate , 2003 .

[14]  J. L. Yang,et al.  Measurement methods for longitudinal surface strain in trees: a review , 2005 .

[15]  Chris Harwood,et al.  Intra-specific competition and the radial development of wood density, microfibril angle and modulus of elasticity in plantation-grown Eucalyptus nitens , 2012, Trees.

[16]  Johannes Fehrmann,et al.  Veneer Grade Analysis of Early to Mid-rotation Plantation Eucalyptus Species in Australia , 2014 .

[17]  J. Boyd,et al.  Tree growth stresses—Part IV: Visco-elastic strain recovery , 1972, Wood Science and Technology.

[18]  G. Becker,et al.  Growth Strain in Eucalyptus nitens at Different Stages of Development , 2009 .

[19]  F. Malan.  EUCALYPTUS IMPROVEMENT FOR LUMBER PRODUCTION , 2005 .

[20]  R. Wolfinger,et al.  Comparing the SAS® GLM and MIXED Procedures for Repeated Measures , 1996 .

[21]  Dr. Robert R. Archer,et al.  Growth Stresses and Strains in Trees , 1987, Springer Series in Wood Science.

[22]  F. Malan,et al.  Effect of genotype-by-environment interaction on the wood properties and qualities of four-year-old Eucalyptus grandis and E. grandis hybrids. , 1996 .

[23]  Identification of PCR-based markers linked to wood splitting in Eucalyptus grandis , 2002 .

[24]  Bernard Thibaut,et al.  Tree mechanics and wood mechanics: relating hygrothermal recovery of green wood to the maturation process , 1994 .

[25]  Henri Baillères,et al.  Factors affecting log traits and green rotary-peeled veneer recovery from temperate eucalypt plantations , 2014, Annals of Forest Science.

[26]  C. Loup,et al.  Relationship between tree morphology and growth stress in mature European beech stands , 2013, Annals of Forest Science.

[27]  H. Baillères.  Précontraintes de croissance et propriété mécano-physiques de clones d'Eucalyptus (Pointe Noire - Congo) : hétérogénéités, corrélations et interprétations histologiques , 1994 .

[28]  J. L. Yang,et al.  The impact of log-end splits and spring on sawn recovery of 32-year-old plantation Eucalyptus globulus Labill. , 2005, Holz als Roh- und Werkstoff.

[29]  C. Harwood,et al.  Longitudinal growth strain as a log and wood quality predictor for plantation-grown Eucalyptus nitens sawlogs , 2011, Wood Science and Technology.

[30]  Mijo Gavran,et al.  Australian plantation statistics 2012 update , 2012 .

[31]  Richard F. Baldwin,et al.  Plywood and Veneer-Based Products: Manufacturing Practices , 2016 .

[32]  B. Potts,et al.  Genetic variation in traits affecting sawn timber recovery in plantation-grown Eucalyptus nitens , 2011, Annals of Forest Science.