Behavior of platinum/tantalum as interdigital transducers for SAW devices in high-temperature environments

In this paper, we report on the use of tantalum as adhesion layer for platinum electrodes used in high-temperature SAW devices based on langasite substrates (LGS). Tantalum exhibits a great adhesive strength and a very low mobility through the Pt film, ensuring a device lifetime at 900°C of about one hour in an air atmosphere and at least 20 h under vacuum. The latter is limited by morphological modifications of platinum, starting with the apparition of crystallites on the surface, followed by important terracing and breaking of the film continuity. Secondary neutral mass spectroscopy (SNMS), Auger electron spectroscopy (AES), X-ray diffraction (XRD) measurements, and comparison with iridium-based electrodes allowed us to show that this deterioration is likely intrinsic to platinum film, consisting of agglomeration phenomena. Finally, based on these results, we present a solution that could significantly enhance the lifetime of Pt-based IDTs placed in high-temperature conditions.

[1]  T. Moonlight,et al.  High temperature stability of langasite surface acoustic wave devices , 2008, 2008 IEEE Ultrasonics Symposium.

[2]  L. Reindl,et al.  Properties of radio frequency Rayleigh waves on langasite at elevated temperatures , 2004, IEEE Ultrasonics Symposium, 2004.

[3]  V. Kalinin,et al.  A Second Generation In-Car Tire Pressure Monitoring System Based on Wireless Passive SAW Sensors , 2006, 2006 IEEE International Frequency Control Symposium and Exposition.

[4]  D. J. Frankel,et al.  Performance of Zr and Ti adhesion layers for bonding of platinum metallization to sapphire substrates , 2001 .

[5]  K. Jensen,et al.  Investigation of high-temperature degradation of platinum thin films with an in situ resistance measurement apparatus , 1998 .

[6]  Neil M. White,et al.  Fabrication of high temperature surface acoustic wave devices for sensor applications , 2005 .

[7]  Paul Muralt,et al.  Stabilized Platinum Electrodes for Ferroelectric Film Deposition using Ti, Ta and Zr Adhesion Layers , 1998 .

[8]  M.P. da Cunha,et al.  Platinum and palladium high-temperature transducers on langasite , 2005, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[9]  F. Sarry,et al.  Extraction of COM parameters on Pt/LGS for high temperature SAW sensor , 2008, 2008 IEEE Ultrasonics Symposium.

[10]  T. Moonlight,et al.  P4L-1 Enabling Very High Temperature Acoustic Wave Devices for Sensor & Frequency Control Applications , 2007, 2007 IEEE Ultrasonics Symposium Proceedings.

[11]  R. Fachberger,et al.  Influence of packaging atmospheres on the durability of high-temperature SAW sensors , 2009, 2009 IEEE International Ultrasonics Symposium.

[12]  Thermodynamic Stability and Interfacial Impedance of Solid-Electrolyte Cells with Noble-Metal Electrodes , 1999 .

[13]  Carl V. Thompson,et al.  Capillary instabilities in thin films , 1990 .

[14]  A. W. Groenland,et al.  Stability of thin platinum films implemented in high-temperature microdevices , 2009 .

[15]  V. Kalinin,et al.  Application of Passive SAW Resonant Sensors to Contactless Measurement of the Output Engine Torque in Passenger Cars , 2007, 2007 IEEE International Frequency Control Symposium Joint with the 21st European Frequency and Time Forum.

[16]  E. Burte,et al.  Effect of annealing in oxygen atmosphere on morphological and electrical properties of iridium and ruthenium thin films prepared by liquid delivery MOCVD , 2007 .