Effect of fabrication process on electrical properties of polymer/multi-wall carbon nanotube nanocomposites

Abstract Polymer/carbon nanotubes nanocomposites were fabricated by an in situ polymerization process using multi-wall carbon nanotubes (MWNT) as filler in an epoxy polymer. Effects of curing process, mixing speed, mixing time, addition of ethanol, timing of hardener addition, etc., in the fabrication process on the electrical properties of nanocomposites have been investigated. In the fabrication process, the effective formation of macroscopic conducting network in matrix is most important to enhance the electrical properties of nanocomposites. It was found that the curing temperature and the mixing conditions are key factors in the fabrication process, which influence the formation of conducting network significantly. Therefore, careful design of these factors in the fabrication process is required to achieve high electrical performances of nanocomposites. The experimental percolation threshold of the resultant nanocomposites was around 0.1 wt%. Moreover, a statistical percolation model was built up to numerically investigate the percolation threshold. The experimental electrical conductivity increases from the percolation threshold following a percolation-like power law with the identified critical exponent t as 1.75.

[1]  Milo S. P. Shaffer,et al.  Development of a dispersion process for carbon nanotubes in an epoxy matrix and the resulting electrical properties , 1999 .

[2]  D. Ugarte,et al.  Aligned Carbon Nanotube Films: Production and Optical and Electronic Properties , 1995, Science.

[3]  I. Kinloch,et al.  Ultra-low electrical percolation threshold in carbon-nanotube-epoxy composites , 2003 .

[4]  Darren J. Martin,et al.  Polyethylene multiwalled carbon nanotube composites , 2005 .

[5]  C. Friedrich,et al.  Mechanical properties and electrical conductivity of carbon-nanotube filled polyamide-6 and its blends with acrylonitrile/butadiene/styrene , 2004 .

[6]  Emmanuel Kymakis,et al.  Single-walled carbon nanotube–polymer composites: electrical, optical and structural investigation , 2002 .

[7]  Soo-Jin Park,et al.  Electrical resistivity and rheological behaviors of carbon nanotubes-filled polypropylene composites , 2004 .

[8]  Masaru Matsuo,et al.  Electrical and mechanical properties of polyimide–carbon nanotubes composites fabricated by in situ polymerization , 2005 .

[9]  Petra Pötschke,et al.  Rheological and dielectrical characterization of melt mixed polycarbonate-multiwalled carbon nanotube composites , 2004 .

[10]  M. Newman,et al.  Fast Monte Carlo algorithm for site or bond percolation. , 2001, Physical review. E, Statistical, nonlinear, and soft matter physics.

[11]  Concepción Domingo,et al.  Low Percolation Threshold in Nanocomposites Based on Oxidized Single Wall Carbon Nanotubes and Poly(butylene terephthalate) , 2004 .

[12]  A. Celzard,et al.  Critical concentration in percolating systems containing a high-aspect-ratio filler. , 1996, Physical review. B, Condensed matter.

[13]  I. Balberg,et al.  Cluster structure and conductivity of three-dimensional continuum systems. , 1985, Physical review. A, General physics.

[14]  Takashi Ikuno,et al.  Electronic Transport in Multiwalled Carbon Nanotubes Contacted with Patterned Electrodes , 2004 .

[15]  C. Castellani,et al.  Disordered Systems and Localization , 1982 .

[16]  E. Kymakis,et al.  Electrical properties of single-wall carbon nanotube-polymer composite films , 2006 .

[17]  Karen I. Winey,et al.  A Coagulation Method to Prepare Single-Walled Carbon Nanotube/PMMA Composites and Their Modulus, Electrical Conductivity, and The rmal Stability , 2003 .

[18]  Rodney Andrews,et al.  Fabrication of Carbon Multiwall Nanotube/Polymer Composites by Shear Mixing , 2002 .

[19]  E. Siochi,et al.  Electrical properties of single wall carbon nanotube reinforced polyimide composites , 2003 .

[20]  John Wilkinson,et al.  Aligned single‐wall carbon nanotube polymer composites using an electric field , 2006 .

[21]  Christian A. Martin,et al.  Formation of percolating networks in multi-wall carbon-nanotube–epoxy composites , 2004 .

[22]  Rikio Yokota,et al.  Characterization of multi-walled carbon nanotube/phenylethynyl terminated polyimide composites , 2004 .

[23]  Guangjun Hu,et al.  Low percolation thresholds of electrical conductivity and rheology in poly(ethylene terephthalate) through the networks of multi-walled carbon nanotubes , 2006 .

[24]  J. Fischer,et al.  Coagulation method for preparing single‐walled carbon nanotube/poly(methyl methacrylate) composites and their modulus, electrical conductivity, and thermal stability , 2003 .

[25]  G. Deutscher.  Percolation and Superconductivity , 1984 .

[26]  Werner J. Blau,et al.  Experimental observation of scaling laws for alternating current and direct current conductivity in polymer-carbon nanotube composite thin films , 2002 .