Localized recrystallization and cracking of lead-free solder interconnections under thermal cycling

The failure mechanism of lead-free solder interconnections of chip scale package–sized Ball Grid Array (BGA) component boards under thermal cycling was studied by employing cross-polarized light microscopy, scanning electronic microscopy, electron backscatter diffraction, and nanoindentation. It was determined that the critical solder interconnections were located underneath the chip corners, instead of the corner most interconnections of the package, and the highest strains and stresses were concentrated at the outer neck regions on the component side of the interconnections. Observations of the failure modes were in good agreement with the finite element results. The failure of the interconnections was associated with changes of microstructures by recrystallization in the strain concentration regions of the solder interconnections. Coarsening of intermetallic particles and the disappearance of the boundaries between the primary Sn cells were observed in both cases. The nanoindentation results showed lower hardness of the recrystallized grains compared with the non-recrystallized regions of the same interconnection. The results show that failure modes are dependent on the localized microstructural changes in the strain concentration regions of the interconnections and the crack paths follow the networks of grain boundaries produced by recrystallization.

[1]  Clyde F. Coombs,et al.  Printed Circuits Handbook , 2007 .

[2]  Thomas R. Bieler,et al.  Cyclic twin nucleation in tin-based solder alloys , 2010 .

[3]  P. Schreurs,et al.  Microstructural damage analysis of SnAgCu solder joints and an assessment on indentation procedures , 2005 .

[4]  Thomas R. Bieler,et al.  Crack Development in a Low-Stress PBGA Package due to Continuous Recrystallization Leading to Formation of Orientations with [001] Parallel to the Interface , 2010 .

[5]  Won Kyoung Choi,et al.  Effects of mechanical deformation and annealing on the microstructure and hardness of Pb-free solders , 2003 .

[6]  I. Dutta.  A constitutive model for creep of lead-free solders undergoing strain-enhanced microstructural coarsening: A first report , 2003 .

[7]  Ganesh Subbarayan,et al.  Microstructural coarsening in Sn-Ag-based solders and its effects on mechanical properties , 2009 .

[8]  C. Handwerker,et al.  Experimental and thermodynamic assessment of Sn-Ag-Cu solder alloys , 2000 .

[9]  W. B. Pearson,et al.  A handbook of lattice spacings and structures of metals and alloys , 1958 .

[10]  Ephraim Suhir,et al.  Micro- and opto-electronic materials and structures : physics, mechanics, design, reliability, packaging , 2007 .

[11]  Sung K. Kang,et al.  The microstructure of Sn in near-eutectic Sn–Ag–Cu alloy solder joints and its role in thermomechanical fatigue , 2004 .

[12]  T. Laurila,et al.  Metallurgical factors behind the reliability of high density lead-free interconnections , 2006 .

[13]  J. Shang,et al.  Mechanical fatigue of Sn-rich Pb-free solder alloys , 2006 .

[14]  M. Tanaka,et al.  Effect of fine dispersoids and anisotropic nature of β-Sn on thermal fatigue properties of flip chips connected by Sn–xAg–0·5Cu (x: 1, 3 and 4 mass-%) lead free solders , 2009 .

[15]  S. Terashima,et al.  Thermal Fatigue Properties of Sn-1.2Ag-0.5Cu-xNi Flip Chip Interconnects , 2004 .

[16]  Masako Nozaki,et al.  Recrystallization of Sn Grains due to Thermal Strain in Sn-1.2Ag-0.5Cu-0.05Ni Solder , 2004 .

[17]  L. Anand.  Constitutive Equations for the Rate-Dependent Deformation of Metals at Elevated Temperatures , 1982 .

[18]  Da-Yuan Shih,et al.  The Crystal Orientation of β-Sn Grains in Sn-Ag and Sn-Cu Solders Affected by Their Interfacial Reactions with Cu and Ni(P) Under Bump Metallurgy , 2009 .

[19]  T. Mattila,et al.  The Role of Recrystallization in the Failure of SnAgCu Solder Interconnections Under Thermomechanical Loading , 2010, IEEE Transactions on Components and Packaging Technologies.

[20]  Farhang Pourboghrat,et al.  Incremental recrystallization/grain growth driven by elastic strain energy release in a thermomechanically fatigued lead-free solder joint , 2007 .

[21]  T. Mattila,et al.  Impact of printed wiring board coatings on the reliability of lead-free chip-scale package interconnections , 2004 .

[22]  Janne J. Sundelin,et al.  Recrystallization behaviour of SnAgCu solder joints , 2008 .

[23]  K. Tu,et al.  Six cases of reliability study of Pb-free solder joints in electronic packaging technology , 2002 .

[24]  Dae-Gon Kim,et al.  Evaluation of solder joint reliability in flip-chip packages during accelerated testing , 2005 .

[25]  Guna S Selvaduray,et al.  Solder joint fatigue models: review and applicability to chip scale packages , 2000 .

[26]  Jun Chen,et al.  Reliability testing of WLCSP lead-free solder joints , 2006 .

[27]  P. Vianco,et al.  Time-independent mechanical and physical properties of the ternary 95.5Sn-3.9Ag-0.6Cu solder , 2003 .

[28]  M. Tanaka,et al.  Improvement of Thermal Fatigue Properties of Sn-Ag-Cu Lead-Free Solder Interconnects on Casio’s Wafer-Level Packages Based on Morphology and Grain Boundary Character , 2009 .

[29]  Alice C. Kilgo,et al.  Creep behavior of the ternary 95.5Sn-3.9Ag-0.6Cu solder: Part II—Aged condition , 2004 .