Brittle Removal Mechanism of Ductile Materials With Ultrahigh-Speed Machining

[1]  S. To,et al.  Serrated chip formation and their adiabatic analysis by using the constitutive model of titanium alloy in high speed cutting , 2015 .

[2]  Shanmugam Murugappan,et al.  Validation of computational fluid dynamics methodology used for human upper airway flow simulations. , 2009, Journal of biomechanics.

[3]  J. Klepaczko,et al.  Numerical study of the critical impact velocity in shear , 1996 .

[4]  Yuebin Guo,et al.  A FEM study on mechanisms of discontinuous chip formation in hard machining , 2004 .

[5]  Zhanqiang Liu,et al.  Serrated chip formation mechanism based on mixed mode of ductile fracture and adiabatic shear , 2014 .

[6]  Guy Sutter,et al.  Chip geometries during high-speed machining for orthogonal cutting conditions , 2005 .

[7]  A. Schmidt,et al.  Hybrid CO2 Laser/Waterjet Machining of Polycrystalline Diamond Substrate: Material Separation Through Transformation Induced Controlled Fracture , 2014 .

[8]  Miaoquan Li,et al.  The flow behavior and constitutive equations in isothermal compression of 7050 aluminum alloy , 2012 .

[9]  P. Chevrier,et al.  Investigation of surface integrity in high speed end milling of a low alloyed steel , 2003 .

[10]  A. Senthil Kumar,et al.  A review on the current research trends in ductile regime machining , 2012 .

[11]  Suhas S. Joshi,et al.  MECHANISM OF CHIP FORMATION IN HIGH-SPEED TURNING OF INCONEL 718 , 2011 .

[12]  J. Knott,et al.  The ductile-brittle transition for nominally pure polycrystalline nickel , 2013 .

[13]  A. Molinari,et al.  Adiabatic shear banding in high speed machining of Ti-6Al-4V: experiments and modeling , 2002 .

[14]  Pol Duwez,et al.  The Propagation of Plastic Deformation in Solids , 1950 .

[15]  Zhanqiang Liu,et al.  Analytical and experimental study on formation of concentrated shear band of saw tooth chip in high-speed machining , 2013 .

[16]  Guénaël Germain,et al.  Identification of Material Constitutive Laws Representative of Machining Conditions for Two Titanium Alloys: Ti6Al4V and Ti555-3 , 2013 .

[17]  R. Scattergood,et al.  Ductile-Regime Grinding: A New Technology for Machining Brittle Materials , 1991 .

[18]  Yuebin B. Guo,et al.  Unified Criterion for Brittle–Ductile Transition in Mechanical Microcutting of Brittle Materials , 2014 .

[19]  Jeffrey J. DeMange,et al.  Effects of material microstructure on blunt projectile penetration of a nickel-based super alloy , 2009 .

[20]  G. List,et al.  Very high speed cutting of Ti–6Al–4V titanium alloy – change in morphology and mechanism of chip formation , 2013 .

[21]  Wong Yoke San,et al.  Ultraprecision ductile mode machining of glass by micromilling process , 2011 .

[22]  I. S. Jawahir,et al.  Some Observations of the Chip Formation Process and the White Layer Formation in High Speed Milling of Hardened Steel , 2004 .

[23]  V. Astakhov,et al.  A METHODOLOGY FOR PRACTICAL CUTTING FORCE EVALUATION BASED ON THE ENERGY SPENT IN THE CUTTING SYSTEM , 2008 .

[24]  Joseph Edward Shigley,et al.  Mechanical engineering design , 1972 .

[25]  Jun Shimizu,et al.  Material removal mechanism beyond plastic wave propagation rate , 2003 .

[26]  G. Byrne,et al.  The mechanisms of chip formation in machining hardened steels , 2002 .

[27]  Alain Molinari,et al.  Strain, strain rate and velocity fields determination at very high cutting speed , 2013 .

[28]  I. Jawahir,et al.  Evaluation of Chip Morphology in Hard Turning Using Constitutive Models and Material Property Data , 2001, Manufacturing Engineering.

[29]  Liu Zhanqiang,et al.  Characteristics of chip evolution with elevating cutting speed from low to very high , 2012 .

[30]  Zhanqiang Liu,et al.  Investigations of yield stress, fracture toughness, and energy distribution in high speed orthogonal cutting , 2013 .