Jet electrochemical machining of TB6 titanium alloy

TB6 titanium alloy (Ti-10V-2Fe-3Al) is a prospective material to replace the traditional titanium alloys in aviation industry due to its excellent comprehensive properties. However, machining of TB6 titanium alloy with traditional processes is characterized by the low machining efficiency, high tool wear, reduced machining accuracy, and inferior surface finish. Electrochemical machining (ECM) is a potential processing technology for titanium alloy, but almost no investigation has been performed on TB6. This paper aims to study the feasibility and select the optimum process parameters for Jet-ECM machining of TB6 titanium alloy. The dissolution behavior of TB6 titanium alloy in sodium nitrate and sodium chloride electrolyte with different concentration and temperature is analyzed. Then, the effect of main parameters, including the composition and concentration of electrolyte, machining voltage, electrolyte flow rate, and inter-electrode gap (IEG), on machining performance is investigated in detail. From experiments, 24 V voltage, 0.6 mm IEG, 2.1 L/min flow rate, and 15 % sodium chloride electrolyte are selected as optimum parameters. The experimental results by using the chosen parameters reveal that the comprehensive machining performance, including material removal rate (10.062 g/min), surface toughness (0.231 μm), taper (2.5), and average overcut (1.01 mm), is acceptable from the viewpoint of industry.

[1]  M. Stolpe,et al.  Electrochemical dissolution behaviour of Ti90Al6V4 and Ti60Al40 used for ECM applications , 2015, Journal of Solid State Electrochemistry.

[2]  David K. Aspinwall,et al.  Machinability and surface integrity of RR1000 nickel based superalloy , 2011 .

[3]  David K. Aspinwall,et al.  PRODUCTIVITY AND WORKPIECE SURFACE INTEGRITY WHEN WEDM AEROSPACE ALLOYS USING COATED WIRES , 2011 .

[4]  B. Su,et al.  Micropatterning of titanium surfaces using electrochemical micromachining with an ethylene glycol electrolyte , 2011 .

[5]  Hubert Chanson,et al.  Current knowledge in hydraulic jumps and related phenomena: A survey of experimental results , 2009 .

[6]  Fritz Klocke,et al.  Technological and Economical Capabilities of Manufacturing Titanium- and Nickel-Based Alloys via Electrochemical Machining (ECM) , 2012 .

[7]  J. Deconinck,et al.  Study of the effects of heat removal on the copying accuracy of the electrochemical machining process , 2011 .

[8]  Zhengyang Xu,et al.  Experimental Investigation on Electrochemical Machining of γ-TiAl Intermetallic , 2015 .

[9]  Masanori Kunieda,et al.  Research on generation of three-dimensional surface with micro-electrolyte jet machining , 2008 .

[10]  Gideon Levy,et al.  Turbomachinery component manufacture by application of electrochemical, electro-physical and photonic processes , 2014 .

[11]  M. Hackert-Oschätzchen,et al.  Generation of Complex Surfaces by Superimposed Multi-dimensional Motion in Electrochemical Machining☆ , 2016 .

[12]  John Fay Wilson,et al.  Practice and theory of electrochemical machining , 1971 .

[13]  Atanas Ivanov,et al.  Recent developments and research challenges in electrochemical micromachining (µECM) , 2013 .

[14]  Stefano Tornincasa,et al.  Electron-Jet Drilling — Basic Involved Phenomena , 1981 .

[15]  Kamlakar P Rajurkar,et al.  New Developments in Electro-Chemical Machining , 1999 .

[16]  Paola Pozzi,et al.  Robust anodic colouring of titanium: Effect of electrolyte and colour durability , 2016 .

[17]  J. A. McGeough,et al.  Principles of electrochemical machining , 1974 .

[18]  J. Schultze,et al.  Electrochemical machining of the steel 100Cr6 in aqueous NaCl and NaNO3 solutions: microstructure of surface films formed by carbides , 2001 .

[19]  Li Shi-kai.  Present State of Research on Ti-1023 Titanium Alloy , 2009 .

[20]  M. Lohrengel,et al.  Electrochemical Machining—mechanisms of anodic dissolution , 2016 .

[21]  J. Bannard.  On the electrochemical machining of some titanium alloys in bromide electrolytes , 1976 .

[22]  Masanori Kunieda,et al.  Mirror-like finishing by electrolyte jet machining , 2015 .

[23]  Andreas Schubert,et al.  Study on the dynamic generation of the jet shape in Jet Electrochemical Machining , 2015 .

[24]  Wei Li,et al.  Wire electrochemical machining with axial electrolyte flushing for titanium alloy , 2013 .

[25]  F. Klocke,et al.  Experimental Research on the Electrochemical Machining of Modern Titanium- and Nickel-based Alloys for Aero Engine Components☆ , 2013 .

[26]  J. W. Schultze,et al.  The surface structure during pulsed ECM of iron in NaNO3 , 2005 .

[27]  R. Schenk.  The Corrosion Properties of Titanium and Titanium Alloys , 2001 .

[28]  Ekkard Brinksmeier,et al.  Surface integrity in material removal processes: Recent advances , 2011 .

[29]  Biswanath Doloi,et al.  Surface characteristics of ECMed titanium work samples for biomedical applications , 2011 .

[30]  Kamlakar P Rajurkar,et al.  Study on the surface integrity of machined tool in micro EDM , 2010 .