A comparative study on roll-to-roll gravure printing on PET and BOPP webs with aqueous ink

Abstract Ink transfer and printing characteristics in high-speed gravure printing were investigated on poly(ethylene terephthalate) (PET) and biaxial-oriented polypropylene (BOPP) substrates employing a pilot-scale gravure printing machine (maximum speed: 500 m min −1 ). The flexible substrates were printed in an aqueous ink diluted with ethanol under various machine factors such as printing speed, nip force, and groove size. The printed images and ink transfer efficiency were examined using an optical microscope, UV–visible spectroscopy, and an atomic force microscope (AFM). A quantitative study was performed on the measurements and estimation of interfacial tension, the work of adhesion, and the contact angle between the ink and the substrates to correlate with the printed features. According to the experimental results, the most critical factors affecting the print features were interpreted to be the viscosity and surface tension of the ink, and interfacial tension. The spreading coefficients of the diluted inks were below zero on both the PET and BOPP films, indicating that spreading hardly occurs spontaneously, and thus limited spreading may be associated with a shear-induced flow of ink. Among tested machine factors, the printing speed did not significantly affect the uniformity and chromaticity of the image on the PET web as observed under microscopy or spectrometry. On the other hand, those on the BOPP film were found to heavily depend upon roller speed and thus dwell time. This difference was attributed to low spreadability of the ink due to capillary immobilization effect on the porous BOPP surface. In addition, the increasing groove size (dot%) resulted in a higher chromaticity due to a larger contact area between ink and substrate. Especially in the case of BOPP, the chromaticity of the printed image increased linearly with increasing dot%. It should be also noted that the images printed on BOPP exhibited enormously higher chromaticity and thickness compared with those on PET at the same dilution and machine factors. The large difference in ink transfer efficiency between the BOPP and PET substrates may be explained partly by the difference in interfacial tension and absorption of the BOPP substrate.

[1]  L. Pauchard,et al.  Non-Newtonian effects on ribbing instability threshold , 2002 .

[2]  G. Briggs,et al.  Pressure-dependent permeation of noble gases (He, Ne, Ar, Kr, Xe) through thin membranes of oriented polypropylene (OPP) studied by mass spectrometry. , 2001 .

[3]  B. Müller,et al.  Coatings Formulation , 2006 .

[4]  S. Leppävuori,et al.  Printing parameters and ink components affecting ultra-fine-line gravure-offset printing for electronics applications , 2004 .

[5]  Salme Jussila,et al.  Roll-to-roll method for producing polyaniline patterns on paper , 2003 .

[6]  N. Halonen,et al.  Gravure printing of conductive particulate polymer inks on flexible substrates , 2005 .

[7]  N. McIntyre,et al.  Draw-ratio-dependent morphology of biaxially oriented polypropylene films as determined by atomic force microscopy , 2000 .

[8]  S. Ghosh.  Functional coatings : by polymer microencapsulation , 2006 .

[9]  S. Leppavuori,et al.  Direct gravure printing (DGP) method for printing fine-line electrical circuits on ceramics , 2004, IEEE Transactions on Electronics Packaging Manufacturing.

[10]  N. Kapur.  A parametric study of direct gravure coating , 2003 .

[11]  D. Shaw,et al.  Introduction to colloid and surface chemistry , 1970 .

[12]  H. Sandberg,et al.  Utilizing roll-to-roll techniques for manufacturing source-drain electrodes for all-polymer transistors , 2005 .

[13]  S. Leppävuori,et al.  Roller-type gravure offset printing of conductive inks for high-resolution printing on ceramic substrates , 2005 .

[14]  Tomi Haatainen,et al.  Continuous roll to roll nanoimprinting of inherently conducting polyaniline , 2007 .

[15]  SY El-Sayad,et al.  Some factors affecting ink transfer in gravure printing , 2002 .

[16]  Marko Pudas,et al.  The absorption ink transfer mechanism of gravure offset printing for electronic circuitry , 2002 .

[17]  Hadj Benkreira,et al.  Direct forward gravure coating on unsupported web , 1998 .

[18]  Bernd Stannowski,et al.  Helianthos : Roll-to-Roll deposition of flexible solar cell modules , 2007 .

[19]  Terho Kololuoma,et al.  Dynamic preparation of TiO2 films for fabrication of dye-sensitized solar cells , 2006 .