Lubrication analysis and sub-surface stress field of an automotive differential hypoid gear pair under dynamic loading

Film thickness and sub-surface stress distribution in a highly loaded automotive differential hypoid gear pair are examined. A 4-Degree of Freedom torsional gear dynamics model, taking into account the torsional stiffness of the pinion and the gear shafts, is used in order to evaluate the contact load, the surface velocities and the contact radii of curvature of the mating teeth during a full meshing cycle. The torsional gear dynamics model takes into account both the geometric non-linearities of the system (backlash non-linearity) as well as the time varying properties (contact radii, meshing stiffness) and the internal excitations caused by geometrical imperfections of the teeth pair (static transmission error). The input torque used for the study of the film thickness and the sub-surface stress distribution corresponds to the region after the main resonance, where no teeth separation occurs. The contact conditions predicted by the gear dynamics are used as the input for the elastohydrodynamic elliptical point contact analysis. The lubricant film thickness, the corresponding pressure and surface traction distributions are obtained quasi-statically using the output load of the dynamic gear pair model. The variation of the induced sub-surface stress field is determined throughout a meshing cycle. Based on the sub-surface reversing orthogonal shear stresses, marginal differences occur when the viscous shear on the conjunctional surfaces are taken into account, which are mainly influenced by the applied pressure distribution. The numerical prediction of lubricant film thickness agrees reasonably well with that predicted using the well-established extrapolated oil film thickness formulae reported in the literature.

[1]  Sheng Li,et al.  A thermal tribo-dynamic mechanical power loss model for spur gear Pairs , 2015 .

[2]  Sheng Li,et al.  Prediction of mechanical gear mesh efficiency of hypoid gear pairs , 2010 .

[3]  M. Huber,et al.  Zur Theorie der Berührung fester elastischer Körper , 1904 .

[4]  Homer Rahnejat,et al.  Elastohydrodynamic lubrication of hypoid gear pairs at high loads , 2012 .

[5]  W. 0. Winer,et al.  Correlational Aspects of the Viscosity-Temperature-Pressure Relationship of Lubricating Oils(Dr In dissertation at Technical University of Delft, 1966) , 1966 .

[6]  Sheng Li,et al.  A tribo-dynamic model of a spur gear pair , 2013 .

[7]  Homer Rahnejat,et al.  The Effect of Vehicle Cruising Speed on the Dynamics of Automotive Hypoid Gears , 2012 .

[8]  Homer Rahnejat,et al.  Non-Newtonian mixed elastohydrodynamics of differential hypoid gears at high loads , 2014 .

[9]  Homer Rahnejat,et al.  Prediction of oil-film thickness and shape in elliptical point contacts under combined rolling and sliding motion , 2000 .

[10]  Vilmos Simon Influence of machine tool setting parameters on EHD lubrication in hypoid gears , 2009 .

[11]  D. Dowson,et al.  Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part IV—Starvation Results , 1976 .

[12]  Teik C. Lim,et al.  Time-Varying Non-Linear Dynamics of a Hypoid Gear Pair for Rear Axle Applications , 2007 .

[13]  L. Houpert,et al.  New Results of Traction Force Calculations in Elastohydrodynamic Contacts , 1985 .

[14]  Vilmos Simon,et al.  Design and Manufacture of Spiral Bevel Gears With Reduced Transmission Errors , 2009 .

[15]  Uwe Gaiser,et al.  The Ultimate Motion Graph , 2000 .

[16]  Stephanos Theodossiades,et al.  An Alternative Formulation of the Dynamic Transmission Error to Study the Oscillations of Automotive Hypoid Gears , 2014 .

[17]  K. Johnson Contact Mechanics: Frontmatter , 1985 .

[18]  A Mostofi,et al.  The incorporation of damping in lumped-parameter modelling techniques , 1999 .

[19]  E. Broszeit,et al.  Internal Stresses and Their Influence on Material Stresses in Hertzian Contacts—Calculations With Different Stress Hypotheses , 1986 .

[20]  Homer Rahnejat,et al.  Transmission efficiency and noise, vibration and harshness refinement of differential hypoid gear pairs , 2014 .

[21]  Faydor L. Litvin,et al.  Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform”—Part 2. Machine Setting Calculations for the Pinions of Formate and Helixform Gears , 1981 .

[22]  H. Rahnejat,et al.  Fundamentals Of Tribology , 2008 .

[23]  Homer Rahnejat,et al.  Multi-body dynamics : monitoring and simulation techniques , 1997 .

[24]  P. M. Johns-Rahnejat Pressure and stress distribution under elastohydrodynamic point contacts , 1988 .

[25]  Jing Wang,et al.  Thermal elastohydrodynamic lubrication of starved elliptical contacts , 2009 .

[26]  Ioannis Karagiannis,et al.  Tribo-dynamic analysis of hypoid gears in automotive differentials , 2013 .

[27]  D. Dowson,et al.  Elasto-hydrodynamic lubrication , 1977 .

[28]  Vilmos Simon Optimal Tooth Modifications in Hypoid Gears , 2003 .

[29]  Rajendra Singh,et al.  Non-linear dynamics of a spur gear pair , 1990 .

[30]  J A Greenwood,et al.  Film Thicknesses in Circular Elastohydrodynamic Contacts , 1988 .

[31]  Faydor L. Litvin,et al.  Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform”—Part 3. Analysis and Optimal Synthesis Methods For Mismatch Gearing and its Application For Hypoid Gears of “Formate” and “Helixform” , 1981 .

[32]  Homer Rahnejat,et al.  Multiphysics Investigations on the Dynamics of Differential Hypoid Gears , 2014 .

[33]  J. L. Tevaarwerk,et al.  Subsurface stress evaluations under rolling/sliding contacts , 1984 .

[34]  I. Karagiannis,et al.  On the dynamics of lubricated hypoid gears , 2012 .

[35]  Duncan Dowson,et al.  A theoretical analysis of the isothermal elastohydrodynamic lubrication of concentrated contacts. I. Direction of lubricant entrainment coincident with the major axis of the Hertzian contact ellipse , 1985, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[36]  Teik C. Lim,et al.  Dynamics of a hypoid gear pair considering the effects of time-varying mesh parameters and backlash nonlinearity , 2007 .

[37]  Brian Schwarz,et al.  Proportional Damping from Experimental Data , 2014 .

[38]  Faydor L. Litvin,et al.  Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform”—Part 1. Calculations For Machine Settings For Member Gear Manufacture of the Formate and Helixform Hypoid Gears , 1981 .

[39]  J. Barbera,et al.  Contact mechanics , 1999 .