Continuous monitoring of tightening condition of single-lap bolted composite joints using intrinsic mode functions of acoustic emission signals: a proof-of-concept study

Intrinsic mode functions of acoustic emission signals, extracted from signals using empirical mode decomposition, were used to characterize the contact conditions of asperities (e.g. sliding friction or collision) in the mating parts of bolted composite joints undergone flexural vibration, whereby to evaluate the tightening condition of the joints quantitatively. Specifically, the sliding friction–related intrinsic mode functions, generated in the mating parts of the two joining composite components (termed as C-C contact), were ascertained from those generated from the contacts between the joining components and metallic fasteners (termed as M-C contact), via a Hilbert–Huang transform. Subsequently, the C-C contact–related intrinsic mode functions were linked to the contact behaviors of asperities at the joining interfaces, reflecting quantitatively the degree of the residual torque of the bolted joints. The fatigue performance of the joints was further evaluated according to the changes in the energy ratios of the C-C contact–related intrinsic mode functions. Experimental results have revealed that the gross energy of acoustic emission signals is capable of evaluating the residual torque of the joints within a limited range. Vibration loosening of composite joints was found to result in an increase in the energy ratios of C-C contact–related high-frequency intrinsic mode functions, on which basis the detectability of the acoustic emission–based structural health monitoring is further improved, making it possible to evaluate the tightening condition of a bolted joint when the joint undergoes vibration fatigue. This proof-of-concept study provides a promising solution to evaluate the contact conditions of bolted composite joints during assembly and to continuously monitor the tightening condition throughout the service life of the joints using the acoustic emission technique.

[1]  Libin Zhao,et al.  An interpretation of the load distributions in highly torqued single-lap composite bolted joints with bolt-hole clearances , 2018 .

[2]  Zhongqing Su,et al.  Quantitative evaluation of residual torque of a loose bolt based on wave energy dissipation and vibro-acoustic modulation: A comparative study , 2016 .

[3]  Hiroshi Fukuda,et al.  The effect of embedded devices on structural integrity of composite laminates , 2016 .

[4]  Zhongqing Su,et al.  A quantitative investigation on vibration durability of viscoelastic relaxation in bolted composite joints , 2016 .

[5]  Fuh-Gwo Yuan,et al.  Damage identification for composite structures using a cross-correlation reverse-time migration technique , 2015 .

[6]  Hoon Sohn,et al.  Locating fatigue damage using temporal signal features of nonlinear Lamb waves , 2015 .

[7]  Omer Faruk Selamet,et al.  Effects of bolt torque and contact resistance on the performance of the polymer electrolyte membrane electrolyzers , 2015 .

[8]  Jianmin Qu,et al.  Nonlinear ultrasonic evaluation of the fatigue damage of adhesive joints , 2015 .

[9]  Qiang Wang,et al.  Modeling nonlinearities of ultrasonic waves for fatigue damage characterization: theory, simulation, and experimental validation. , 2014, Ultrasonics.

[10]  Michael D. Todd,et al.  Monitoring of bearing failure in composite bolted connections using ultrasonic guided waves: A parametric study , 2014 .

[11]  Tadeusz Uhl,et al.  Advanced structural damage detection : from theory to engineering applications , 2013 .

[12]  Wieslaw Ostachowicz,et al.  Guided waves-based damage localization in riveted aircraft panel , 2013, Smart Structures.

[13]  Yaguo Lei,et al.  A review on empirical mode decomposition in fault diagnosis of rotating machinery , 2013 .

[14]  Hassan Jalali,et al.  Micro/macro-slip damping in beams with frictional contact interface , 2012 .

[15]  P. Wilcox,et al.  Modeling and signal processing for guided wave structural health monitoring , 2012 .

[16]  Mannur J. Sundaresan,et al.  Analysis of experimentally generated friction related acoustic emission signals , 2012 .

[17]  Alan Hase,et al.  Correlation between features of acoustic emission signals and mechanical wear mechanisms , 2012 .

[18]  Michele Meo,et al.  Structural health monitoring of bolted joints using linear and nonlinear acoustic/ultrasound methods , 2011 .

[19]  Mannur J. Sundaresan,et al.  Characterization of fretting related acoustic emission signals , 2010, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[20]  Francesco Aymerich,et al.  Experimental Study of Impact-Damage Detection in Composite Laminates using a Cross-Modulation Vibro-Acoustic Technique , 2010 .

[21]  Patrice Masson,et al.  The use of time domain localized structural intensity for damage characterization , 2010 .

[22]  Hiroshi Kato,et al.  Ultrasonic detection of fretting fatigue damage at bolt joints of aluminum alloy plates , 2009 .

[23]  Takashi Ishikawa,et al.  Bearing strength and failure behavior of bolted composite joints (part I: Experimental investigation) , 2005 .

[24]  Chris L. Pettit,et al.  Uncertainties and dynamic problems of bolted joints and other fasteners , 2005 .

[25]  S. S. Shen,et al.  Applications of Hilbert–Huang transform to non‐stationary financial time series analysis , 2003 .

[26]  Qiang Wang,et al.  Characterizing hypervelocity (>2.5 km/s)-impact-engendered damage in shielding structures using in-situ acoustic emission: Simulation and experiment , 2018 .

[27]  Fulei Chu,et al.  HHT-based AE characteristics of natural fatigue cracks in rotating shafts , 2012 .