Friction stir welded T-joints optimization

Abstract The increasing use of aluminium alloys in transportation industry, such as railways, shipbuilding and aeronautics, promotes the development of more efficient and reliable welding processes. Friction stir welding (FSW) is a prominent solid-state joining technology that arose as a possible reliable welding solution. Optimized process parameters are not regularly used in previous studies found in the literature, in particular T-joints, which difficult the process industrial application. This study is focused on the optimization of friction stir welded T-joints using the Taguchi method. Mechanical tests of 27 different welded joints were carried out, and results were analysed using ANOVA, mean effect and response surface methodology (RSM). The tool rotational speed was verified to be the most influent factor in the joint mechanical properties, and is strongly dependent on the shoulder/probe diameters ratio. It was also shown that using 1000 rpm, 3.90 mm of probe depth and shoulder/probe diameters ratio of 2.5 (shoulder diameter of 15 mm) it may be achieved improved joint strength. For the optimized parameters it was verified that the welding speed does not have a significant influence. Equations to predict the joints mechanical properties were also derived through multiple regression.

[1]  Pedro Miguel Moreira,et al.  12.3 – Friction Stir Welding of T-joints Fabricated with Three Parts , 2008 .

[2]  Livan Fratini,et al.  On the FSW of AA2024-T4 and AA7075-T6 T-joints: an industrial case study , 2010 .

[3]  V. Balasubramanian,et al.  Predicting tensile strength of friction stir welded AA6061 aluminium alloy joints by a mathematical model , 2009 .

[4]  Z. Yin,et al.  Investigation of quench sensitivity and transformation kinetics during isothermal treatment in 6082 aluminum alloy , 2011 .

[5]  P. Moreira,et al.  Friction stir welding of T-joints with dissimilar aluminium alloys: Mechanical joint characterisation , 2010 .

[6]  F. Micari,et al.  Material Flow in FSW of T-joints: Experimental and Numerical Analysis , 2008 .

[7]  Livan Fratini,et al.  Friction Stir Welding of AA6082-T6 T-joints: Process Engineering and Performance Measurement , 2006 .

[8]  Abbas S. Milani,et al.  Taguchi Optimization of Process Parameters in Friction Stir Welding of 6061 Aluminum Alloy: A Review and Case Study , 2011 .

[9]  V. Balasubramanian,et al.  Process parameters optimization for friction stir welding of RDE-40 aluminium alloy using Taguchi technique , 2008 .

[10]  Xiaodong Xu,et al.  Characteristics of defects and tensile behaviors on friction stir welded AA6061-T4 T-joints , 2012 .

[11]  E. Lertora,et al.  AA8090 Al-Li Alloy FSW parameters to minimize defects and increase fatigue life , 2010 .

[12]  E. Nazari,et al.  Tensile behavior of friction stir welded AA 6061-T4 aluminum alloy joints , 2012 .

[13]  C. Muralidharan,et al.  Establishing Empirical Relationships to Predict Grain Size and Tensile Strength of Friction Stir Welded AA 6061-T6 Aluminium Alloy Joints , 2010 .

[14]  C. Dalle Donne,et al.  Friction Stir Welding of T-Joints , 2003 .

[15]  Livan Fratini,et al.  Influence of material characteristics on plastomechanics of the FSW process for T-joints , 2009 .

[16]  V. Balasubramanian,et al.  Optimization of process parameters for friction stir welding of cast aluminium alloy A319 by Taguchi method , 2009 .

[17]  P. Moreira,et al.  Fatigue Behaviour of FS, LB and MIG Welds of AA6061-T6 and AA6082-T6 , 2008 .

[18]  F. Micari,et al.  Experimental Characterization of FSW T-Joints of Light Alloys , 2007 .