Pressure infiltration of Al–12 wt.% Si–X (X = Cu, Ti, Mg) alloys into graphite particle preforms

Abstract The pressure infiltration of Al and Al–12 wt.% Si–X alloys into preforms of packed graphite particles has been investigated. Compacts were prepared from particles of average diameter of 15, 27, 64, and 124 μm. While infiltration with pure Al at 750 °C was poor due to both gasification of graphite and reaction between C and Al, the lower infiltration temperature used for the Al–Si eutectic alloy improved infiltration performance. Results for the threshold pressure and infiltration kinetics are discussed in the light of previously published results. Ti (up to 1.5 wt.%) and Cu (up to 1.0 wt.%) additions were found to have no effect on pressure infiltration. However, Mg additions (up to 4 wt.%) significantly decreased the threshold pressure, as a consequence of the decrease in surface tension of Al promoted by this element. Coating the graphite particles with a chemical compound that dissolves the oxide layer reduces the threshold pressure, although this has limited technological applicability due to the increase in porosity. The compact permeability derived from infiltration of the alloys is compared with the intrinsic permeability obtained through infiltration of a wetting organic fluid.

[1]  F. Delannay,et al.  The wetting of solids by molten metals and its relation to the preparation of metal-matrix composites composites , 1987 .

[2]  C. Garcia-cordovilla,et al.  Effects of temperature on pressure infiltration of packed SiC particulates by liquid aluminium , 1995 .

[3]  N. Sobczak,et al.  Interaction Between Porous Graphite Substrate and Liquid or Semi-Liquid Aluminium Alloys Containing Titanium , 1996 .

[4]  C. Garcia-cordovilla,et al.  Evaluation of the wettability of liquid aluminum with ceramic particulates (SiC, TiC, AI2O3) by means of pressure infiltration , 1993, Metallurgical and Materials Transactions A.

[5]  J. Goicoechea,et al.  Surface tension of binary and ternary aluminium alloys of the systems Al-Si-Mg and Al-Zn-Mg , 1992 .

[6]  Processes,et al.  Advanced structural materials , 1992 .

[7]  E. Lavernia,et al.  Processing techniques for particulate-reinforced metal aluminium matrix composites , 1991 .

[8]  C. Garcia-cordovilla,et al.  Factors affecting pressure infiltration of packed SiC particulates by liquid aluminum , 1995 .

[9]  C. Garcia-cordovilla,et al.  The surface tension of liquid pure aluminium and aluminium-magnesium alloy , 1986 .

[10]  C. Garcia-cordovilla,et al.  Pressure infiltration of packed ceramic particulates by liquid metals , 1999 .

[11]  C. Garcia-cordovilla,et al.  Wettability of binary and ternary alloys of the system Al-Si-Mg with SiC particulates , 1994 .

[12]  C. Garcia-cordovilla,et al.  Threshold pressure for infiltration and particle specific surface area of particle compacts with bimodal size distributions , 2004 .

[13]  S. Schamm,et al.  The K2ZrF6 wetting process: Effect of surface chemistry on the ability of a SiC-Fiber preform to be impregnated by aluminum , 1991 .

[14]  R. Naslain,et al.  A new casting process for carbon (or SiC-based) fibre-aluminium matrix low-cost composite materials , 1985 .

[15]  P. Uggowitzer,et al.  Physical properties of graphite/aluminium composites produced by gas pressure infiltration method , 2003 .

[16]  C. Garcia-cordovilla,et al.  Pressure infiltration of liquid aluminium into packed SiC particulate with a bimodal size distribution , 2002 .

[17]  C. Garcia-cordovilla,et al.  Interfacial tensions and threshold pressure for infiltration of packed ceramic particulate by Al-Sn and Al-Pb alloys , 2001 .

[18]  C. Garcia-cordovilla,et al.  Effect of K2ZrF6 coatings on pressure infiltration of packed SiC particulates by liquid aluminum , 1993 .

[19]  H. Ye,et al.  An overview of the development of Al-Si-Alloy based material for engine applications , 2003 .

[20]  J. Bear.  Dynamics of Fluids in Porous Media , 1975 .

[21]  K. Landry,et al.  Wettability of carbon by aluminum and aluminum alloys , 1998 .

[22]  V. Michaud,et al.  Infiltration processing of fibre reinforced composites: governing phenomena , 2001 .

[23]  C. Garcia-cordovilla,et al.  Effects of nitrogen on the surface tension of pure aluminium at high temperatures , 2001 .

[24]  H. Atkinson,et al.  Effect of Alloying Additions on Threshold Pressure for Infiltration and Porosity of Aluminium-Based Melt Infiltrated Silicon Carbide Powder Compacts , 1996 .