Minimum Quantity Lubrication (MQL) in Machining: Benefits and Drawbacks

 Abstract—Micro lubrication or also known as minimum quantity lubrication (MQL) serves as an alternative to flood cooling by reducing the volume of cutting fluid used in the machining process; but not without significant health concerns. Flood cooling is primarily used to cool and lubricate the cutting tool and work piece interface during machining process. The adverse health effects caused by the use of coolants and the potential economic advantages of greener machining methods are drawing manufacturer’s attention to adapt and develop new methods of using lubricants. The objective of this paper is to review the state of the art literature in machining using MQL, highlight the benefits, but also stress the adverse health effects of using minimum quantity lubrication. Finally we highlight areas of relevant future research.

[1]  A. S. Varadarajan,et al.  Simulation of surface milling of hardened AISI4340 steel with minimal fluid application using artificial neural network , 2012 .

[2]  German Fox-Rabinovich,et al.  Enhancement of Wet- and MQL-Based Machining of Automotive Alloys Using Cutting Tools with DLC/Polymer Surface Treatments , 2008 .

[3]  Fumihiro Itoigawa,et al.  Effects and mechanisms in minimal quantity lubrication machining of an aluminum alloy , 2006 .

[4]  Song Zhang,et al.  Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions , 2012 .

[5]  A. D. Jayal,et al.  Effects of cutting fluid application on tool wear in machining: Interactions with tool-coatings and tool surface features , 2009 .

[6]  R. E. Chalmers.  GLOBAL FLAVOR HIGHLIGHTS NAMRC XXVII , 1999 .

[7]  V.T.G. Naves,et al.  Evaluation of the effect of application of cutting fluid at high pressure on tool wear during turning operation of AISI 316 austenitic stainless steel , 2013 .

[8]  N. R. Dhar,et al.  Performance evaluation of minimum quantity lubrication by vegetable oil in terms of cutting force, cutting zone temperature, tool wear, job dimension and surface finish in turning AISI-1060 steel , 2006 .

[9]  Aldo Attanasio,et al.  Minimal quantity lubrication in turning: Effect on tool wear , 2006 .

[10]  Robert Heinemann,et al.  Effect of MQL on the tool life of small twist drills in deep-hole drilling , 2006 .

[11]  Yunn-Shiuan Liao,et al.  Mechanism of minimum quantity lubrication in high-speed milling of hardened steel , 2007 .

[12]  Ichiro Inasaki,et al.  TRIBOLOGICAL ACTION AND OPTIMAL PERFORMANCE: RESEARCH ACTIVITIES REGARDING MQL MACHINING FLUIDS , 2006 .

[13]  Imtiaz Ahmed Choudhury,et al.  Application of vegetable oil-based metalworking fluids in machining ferrous metals—A review , 2012 .

[14]  A. Cole,et al.  Going green. , 2010, Mental health today.

[15]  Donguk Park.  The Occupational Exposure Limit for Fluid Aerosol Generated in Metalworking Operations: Limitations and Recommendations , 2012, Safety and health at work.

[16]  Walter Lindolfo Weingaertner,et al.  Analysis of temperature during drilling of Ti6Al4V with minimal quantity of lubricant , 2006 .

[17]  Taghi Tawakoli,et al.  An investigation on surface grinding of AISI 4140 hardened steel using minimum quantity lubrication-MQL technique , 2010 .

[18]  Richard J. Furness,et al.  Minimum Quantity Lubrication (MQL) Machining for Complex Powertrain Components , 2006 .

[19]  Steven Y. Liang,et al.  Performance profiling of minimum quantity lubrication in machining , 2007 .

[20]  Qian Zou,et al.  Cutting insert and work piece materials for minimum quantity lubrication , 2010, Other Conferences.

[21]  Hans Thordenberg,et al.  An experimental investigation on contact length during minimum quantity lubrication (MQL) machining , 2008 .

[22]  S. H. Tomadi,et al.  Failure mode analysis of carbide cutting tools used for machining titanium alloy , 2013 .

[23]  Imtiaz Ahmed Choudhury,et al.  Developments in the formulation and application of vegetable oil-based metalworking fluids in turning process , 2013 .

[24]  D. Kramar,et al.  Wear behavior and cutting performance of nanostructured hard coatings on cemented carbide cutting tools in hard milling , 2013 .

[25]  Matthew T. Siniawski,et al.  Metal working fluids: finding green in the manufacturing process , 2009 .

[26]  E. O. Bennett,et al.  Occupational airway diseases in the metalworking industry Part 1: Respiratory infections, pneumonia, chronic bronchitis and emphysema , 1985 .

[27]  K. Aslantaş,et al.  An experimental investigation of the effect of coating material on tool wear in micro milling of Inconel 718 super alloy , 2013 .

[28]  Christoph Herrmann,et al.  Ecological and economic evaluation of a novel glycerol based biocide-free metalworking fluid , 2013 .

[29]  Myung-Chang Kang,et al.  Effect of the minimum quantity lubrication in high-speed end-milling of AISI D2 cold-worked die steel (62 HRC) by coated carbide tools , 2008 .

[30]  Andres F. Clarens,et al.  Analytical model of metalworking fluid penetration into the flank contact zone in orthogonal cutting , 2013 .

[31]  H. J. Heine,et al.  DRY MACHINING : A PROMISING OPTION , 1998 .

[32]  J. Rozzi,et al.  The Experimental and Theoretical Evaluation of an Indirect Cooling System for Machining , 2011 .

[33]  Mohammed Nouari,et al.  Modeling of velocity-dependent chip flow angle and experimental analysis when machining 304L austenitic stainless steel with groove coated-carbide tools , 2013 .

[34]  P. Sreejith,et al.  Dry machining: Machining of the future , 2000 .

[35]  Hassan Abdalla,et al.  Development of novel sustainable neat-oil metal working fluids for stainless steel and titanium alloy machining. Part 1. Formulation development , 2007 .

[36]  Uwe Heisel,et al.  Burr formation in short hole drilling with minimum quantity lubrication , 2009, Prod. Eng..

[37]  Álisson Rocha Machado,et al.  Tool life and wear mechanisms in high speed machining of Ti–6Al–4V alloy with PCD tools under various coolant pressures , 2013 .