Barriers of commercial power generation using biomass gasification gas: A review

Gasification is one of the promising technologies to convert biomass to gaseous fuels for distributed power generation. However, the commercial exploitation of biomass energy suffers from a number of logistics and technological challenges. In this review, the barriers in each of the steps from the collection of biomass to electricity generation are highlighted. The effects of parameters in supply chain management, pretreatment and conversion of biomass to gas, and cleaning and utilization of gas for power generation are discussed. Based on the studies, until recently, the gasification of biomass and gas cleaning are the most challenging part. For electricity generation, either using engine or gas turbine requires a stringent specification of gas composition and tar concentration in the product gas. Different types of updraft and downdraft gasifiers have been developed for gasification and a number of physical and catalytic tar separation methods have been investigated. However, the most efficient and popular one is yet to be developed for commercial purpose. In fact, the efficient gasification and gas cleaning methods can produce highly burnable gas with less tar content, so as to reduce the total consumption of biomass for a desired quantity of electricity generation. According to the recent report, an advanced gasification method with efficient tar cleaning can significantly reduce the biomass consumption, and thus the logistics and biomass pretreatment problems can be ultimately reduced.

[1]  John S. Cundiff,et al.  Cotton logistics as a model for a biomass transportation system , 2008 .

[2]  Hanif D. Sherali,et al.  A linear programming approach for designing a herbaceous biomass delivery system , 1997 .

[3]  Katsuya Kawamoto,et al.  Bench-scale gasification of cedar wood--part II: effect of operational conditions on contaminant release. , 2013, Chemosphere.

[4]  M. V. Gil,et al.  Gasification of rice straw in a fluidized-bed gasifier for syngas application in close-coupled boiler-gasifier systems. , 2012, Bioresource technology.

[5]  Pekka Ahtila,et al.  Evaluation of energy efficiency in biofuel drying by means of energy and exergy analyses , 2005 .

[6]  Javad Abbasian,et al.  Catalytic decomposition of ammonia in a fuel gas at high temperature and pressure , 1995 .

[7]  Laihong Shen,et al.  Experimental investigation on hydrogen production from biomass gasification in interconnected fluidized beds , 2012 .

[8]  R. N. Singh,et al.  Equilibrium moisture content of biomass briquettes , 2004 .

[9]  Kalyan Annamalai,et al.  Updraft fixed bed gasification of mesquite and juniper wood samples. , 2012 .

[10]  Steffen Heidenreich,et al.  Filtration performance at high temperatures and analysis of ceramic filter elements during biomass gasification , 2011 .

[11]  Hiroshi Iwai,et al.  Performance evaluation of an integrated small-scale SOFC-biomass gasification power generation system , 2012 .

[12]  Katsuya Kawamoto,et al.  Bench-scale gasification of cedar wood--part I: effect of operational conditions on product gas characteristics. , 2013, Chemosphere.

[13]  I. Tatsiopoulos,et al.  Economic aspects of the cotton-stalk biomass logistics and comparison of supply chain methods , 2003 .

[14]  Li Xing,et al.  Renewable energy from agro-residues in China: Solid biofuels and biomass briquetting technology , 2009 .

[15]  Suneerat Pipatmanomai,et al.  Gasification of high moisture rubber woodchip with rubber waste in a bubbling fluidized bed , 2011 .

[16]  R. James Barbour,et al.  Strategic assessment of bioenergy development in the West : biomass resource assessment and supply analysis for the WGA region : final report, Kansas State University and the U.S. Forest Service, September 1, 2008. , 2008 .

[17]  Herbert Vogel,et al.  Catalytic tar removal from bio syngas—Catalyst development and kinetic studies , 2011 .

[18]  Daniel T. Schwartz,et al.  Uncertainty in biomass supply estimates: Lessons from a Yakama Nation case study , 2011 .

[19]  Umberto Arena,et al.  A techno-economic comparison between two design configurations for a small scale, biomass-to-energy gasification based system , 2010 .

[20]  Dana M. Johnson,et al.  A GIS-based method for identifying the optimal location for a facility to convert forest biomass to biofuel , 2011 .

[21]  R. Sparling,et al.  Biomass pretreatment: fundamentals toward application. , 2011, Biotechnology advances.

[22]  Yi Wang,et al.  Catalytic reforming of tar during gasification. Part IV. Changes in the structure of char in the char-supported iron catalyst during reforming , 2013 .

[23]  Xiaoyan Zhu,et al.  Challenges and models in supporting logistics system design for dedicated-biomass-based bioenergy industry. , 2011, Bioresource technology.

[24]  Shahab Sokhansanj,et al.  Technoeconomic analysis of wheat straw densification in the Canadian Prairie Province of Manitoba. , 2012, Bioresource technology.

[25]  Mohammad Asadullah,et al.  Energy efficient production of hydrogen and syngas from biomass: development of low-temperature catalytic process for cellulose gasification. , 2002, Environmental science & technology.

[26]  Chunshan Li,et al.  Development of new nickel based catalyst for biomass tar steam reforming producing H2-rich syngas , 2009 .

[27]  Jagtar Singh,et al.  Geographical distribution of agricultural residues and optimum sites of biomass based power plant in Bathinda, Punjab , 2011 .

[28]  Haifeng Liu,et al.  Research on the flow properties of the blended particles of rice straw and coal , 2012 .

[29]  Jay P. Gore,et al.  Design and analysis of geographic distribution of biomass power plant and satellite storages in China. Part 1: Straight-line delivery. , 2012 .

[30]  Thanh D. B. Nguyen,et al.  Performance evaluation for dual circulating fluidized-bed steam gasifier of biomass using quasi-equilibrium three-stage gasification model , 2011 .

[31]  Dalin Li,et al.  Catalytic performance of manganese-promoted nickel catalysts for the steam reforming of tar from biomass pyrolysis to synthesis gas , 2013 .

[32]  Jasvinder Singh,et al.  Biomass conversion to energy in India—A critique , 2010 .

[33]  Mohammad Asadullah,et al.  A comparison of Rh/CeO2/SiO2 catalysts with steam reforming catalysts, dolomite and inert materials as bed materials in low throughput fluidized bed gasification systems. , 2004 .

[34]  Bo Xiao,et al.  Hydrogen-rich gas production by steam gasification of char from biomass fast pyrolysis in a fixed-bed reactor: influence of temperature and steam on hydrogen yield and syngas composition. , 2010, Bioresource technology.

[35]  Antonio Ruiz Celma,et al.  Design, construction and performance testing of a solar dryer for agroindustrial by-products , 2010 .

[36]  Anchan Paethanom,et al.  Performance of tar removal by absorption and adsorption for biomass gasification , 2012 .

[37]  Alejandro Reyes,et al.  Drying Characteristics of Forest Biomass Particles of Pinus radiata , 2004 .

[38]  F. Verhoeff,et al.  Drying of biomass for second generation synfuel production. , 2010 .

[39]  Daniel Stanghelle,et al.  Granular bed filtration of high temperature biomass gasification gas. , 2007, Journal of hazardous materials.

[40]  Wang Cuiping,et al.  Experimental study on the combustion characteristics of biomass pellets. , 2006 .

[41]  Dingena L. Schott,et al.  Physical properties of solid biomass , 2011 .

[42]  Sibel Ozdogan,et al.  Results with a bench scale downdraft biomass gasifier for agricultural and forestry residues. , 2011 .

[43]  Chuang-zhi Wu,et al.  Hydrogen-rich gas production from biomass air and oxygen/steam gasification in a downdraft gasifier , 2007 .

[44]  Y. Son,et al.  Gasification and power generation characteristics of woody biomass utilizing a downdraft gasifier , 2011 .

[45]  C Freda,et al.  Biomass gasification and in-bed contaminants removal: performance of iron enriched olivine and bauxite in a process of steam/O2 gasification. , 2012, Bioresource technology.

[46]  C Ihi Efficient gasification of wet biomass residue to produce middle caloric gas , 2008 .

[47]  Xiaohui Zhang,et al.  Evaluation of a biomass drying process using waste heat from process industries: A case study , 2012 .

[48]  Victor R Vasquez,et al.  Effect of thermal pretreatment on equilibrium moisture content of lignocellulosic biomass. , 2011, Bioresource technology.

[49]  Peter Lerman,et al.  Experimental method for designing a biomass bed dryer , 2011 .

[50]  Fan Geng,et al.  Experimental study on the space time of flexible filamentous particles in a rotary dryer , 2013 .

[51]  Shahab Sokhansanj,et al.  Bulk density and compaction behavior of knife mill chopped switchgrass, wheat straw, and corn stover. , 2010, Bioresource technology.

[52]  R. Huhnke,et al.  Integrative Investment Appraisal of a Lignocellulosic Biomass-to-Ethanol Industry , 2003 .

[53]  Mohand Tazerout,et al.  Single zone combustion modeling of biodiesel from wastes in diesel engine , 2013 .

[54]  P. Lehtikangas Quality properties of pelletised sawdust, logging residues and bark , 2001 .

[55]  J. V. Doorn,et al.  Ten residual biomass fuels for circulating fluidized-bed gasification , 2001 .

[56]  Mohammad Asadullah,et al.  A novel catalytic process for cellulose gasification to synthesis gas , 2001 .

[57]  Juan F. Pérez,et al.  Effect of biomass particle size and air superficial velocity on the gasification process in a downdraft fixed bed gasifier. An experimental and modelling study , 2008 .

[58]  Zhen-Yu Zhao,et al.  Assessment of the biomass power generation industry in China , 2012 .

[59]  Borja Velázquez-Martí,et al.  Quantification of the residual biomass obtained from pruning of trees in Mediterranean almond groves , 2011 .

[60]  Cheng-Han Lu,et al.  Characterization and comparison of biomass produced from various sources: Suggestions for selection of pretreatment technologies in biomass-to-energy , 2012 .

[61]  Borja Velázquez-Martí,et al.  Quantification of the residual biomass obtained from pruning of trees in Mediterranean olive groves , 2011 .

[62]  Galip Akay,et al.  Occurrence, composition and dew point of tars produced during gasification of fuel cane bagasse in a downdraft gasifier , 2012 .

[63]  Pengfei Zhang,et al.  An assessment model for collecting and transporting cellulosic biomass , 2013 .

[64]  Li Dong,et al.  Potential approaches to improve gasification of high water content biomass rich in cellulose in dual fluidized bed , 2010 .

[65]  Mehri Sanati,et al.  The release of organic compounds during biomass drying depends upon the feedstock and/or altering drying heating medium , 2003 .

[66]  Silvio de Oliveira Junior,et al.  Supercritical steam cycles and biomass integrated gasification combined cycles for sugarcane mills , 2010 .

[67]  Marko P. Hekkert,et al.  The bumpy road of biomass gasification in the Netherlands: Explaining the rise and fall of an emerging innovation system , 2008 .

[68]  Jiří Jaromír Klemeš,et al.  Total footprints-based multi-criteria optimisation of regional biomass energy supply chains , 2012 .

[69]  Philip Peck,et al.  Organisational frameworks for straw-based energy systems in Sweden and Denmark , 2012 .

[70]  J. M. Andrés,et al.  Behaviour of dolomite, olivine and alumina as primary catalysts in air–steam gasification of sewage sludge , 2011 .

[71]  Jay P. Gore,et al.  Design and analysis of geographic distribution of biomass power plant and satellite storages in China. Part 2: Road delivery , 2012 .

[72]  F. V. Tinaut,et al.  Theoretical and experimental study of a direct contact thermal screw dryer for biomass residues , 2005 .

[73]  Chao’en Li,et al.  The undiluted, non-catalytic partial oxidation of methane in a flow tube reactor – An experimental study using indirect induction heating , 2013 .

[74]  Xiangmei Meng,et al.  Biomass gasification in a 100 kWth steam-oxygen blown circulating fluidized bed gasifier: Effects of operational conditions on product gas distribution and tar formation , 2011 .

[75]  Hermann Hofbauer,et al.  Performance improvement of dual fluidized bed gasifiers by temperature reduction: The behavior of tar species in the product gas , 2013 .

[76]  Steffen Heidenreich,et al.  Gas cleaning, gas conditioning and tar abatement by means of a catalytic filter candle in a biomass fluidized-bed gasifier. , 2010, Bioresource technology.

[77]  M. H. Chakrabarti,et al.  The effect of temperature on various parameters in coal, biomass and CO-gasification: A review , 2012 .

[78]  Mohammad Asadullah,et al.  Catalytic reforming of tar during gasification. Part II. Char as a catalyst or as a catalyst support for tar reforming , 2011 .

[79]  Mohammad Asadullah,et al.  Gasification of different biomasses in a dual-bed gasifier system combined with novel catalysts with high energy efficiency , 2004 .

[80]  O. Chin Characteristics of some biomass briquettes prepared under modest die pressures , 2000 .

[81]  Kaoru Fujimoto,et al.  Catalytic Performance of Rh/CeO2 in the Gasification of Cellulose to Synthesis Gas at Low Temperature , 2001 .

[82]  Pinakeswar Mahanta,et al.  Thermodynamic optimization of biomass gasification for decentralized power generation and Fischer–Tropsch synthesis , 2010 .

[83]  R. Chirone,et al.  Biomass gasification in a catalytic fluidized reactor with beds of different materials , 2009 .

[84]  Kitipong Jaojaruek,et al.  Experimental study of wood downdraft gasification for an improved producer gas quality through an innovative two-stage air and premixed air/gas supply approach. , 2011, Bioresource technology.

[85]  David A. Tillman,et al.  Chapter 5 – Herbaceous and Agricultural Biomass Opportunity Fuels , 2004 .

[86]  Stefan Seuring,et al.  Supply chain and logistics issues of bio-energy production. , 2011 .

[87]  Ibrahim Dincer,et al.  Investigation of a multi-generation system using a hybrid steam biomass gasification for hydrogen, p , 2010 .

[88]  G. M. Madhu,et al.  Fouling behaviour, regeneration options and on-line control of biomass-based power plant effluents using microporous ceramic membranes , 2007 .

[89]  David D Jones,et al.  Steam-air fluidized bed gasification of distillers grains: Effects of steam to biomass ratio, equivalence ratio and gasification temperature. , 2009, Bioresource technology.

[90]  R. Ganguly,et al.  Energy and exergy analyses of an externally fired gas turbine (EFGT) cycle integrated with biomass gasifier for distributed power generation , 2010 .

[91]  Li Dong,et al.  An advanced biomass gasification technology with integrated catalytic hot gas cleaning: Part I. Technology and initial experimental results in a lab-scale facility , 2013 .

[92]  Zhijian Pei,et al.  Physical properties of pellets made from sorghum stalk, corn stover, wheat straw, and big bluestem , 2011 .

[93]  Juan P. Sesmero,et al.  Biomass supply schedules for Great Plains delivery points , 2012 .

[94]  Pratik N Sheth,et al.  Experimental studies on producer gas generation from wood waste in a downdraft biomass gasifier. , 2009, Bioresource technology.

[95]  Samsudin Anis,et al.  Tar reduction in biomass producer gas via mechanical, catalytic and thermal methods: A review , 2011 .

[96]  Koichi Yamamoto,et al.  Wood biomass supply costs and potential for biomass energy plants in Japan , 2012 .

[97]  Keywan Riahi,et al.  Determinants of Household Energy Consumption in India , 2010 .

[98]  Xiaoyan Zhu,et al.  Logistics system design for biomass-to-bioenergy industry with multiple types of feedstocks. , 2011, Bioresource technology.

[99]  Mohammad Asadullah,et al.  Demonstration of real biomass gasification drastically promoted by effective catalyst , 2003 .

[100]  Daniele Cocco,et al.  Performance evaluation of small size externally fired gas turbine (EFGT) power plants integrated with direct biomass dryers , 2006 .

[101]  Cassandra Moseley,et al.  A supply chain analysis framework for assessing state-level forest biomass utilization policies in the United States , 2011 .

[102]  S. Sokhansanj,et al.  Effects of compressive force, particle size and moisture content on mechanical properties of biomass pellets from grasses , 2006 .

[103]  Gérald Djéga-Mariadassou,et al.  Steam reforming of model gasification tars compounds on nickel based ceria-zirconia catalysts , 2011 .

[104]  Susanna Nilsson,et al.  Improving the performance of fluidized bed biomass/waste gasifiers for distributed electricity: A new three-stage gasification system , 2013 .

[105]  Ajay Kumar,et al.  Optimization and economic evaluation of industrial gas production and combined heat and power generation from gasification of corn stover and distillers grains. , 2010, Bioresource technology.

[106]  I. Dincer,et al.  Steam and air fed biomass gasification: Comparisons based on energy and exergy , 2012 .

[107]  Kakali Mukhopadhyay,et al.  An assessment of a Biomass Gasification based Power Plant in the Sunderbans. , 2004 .

[108]  Mohammad Asadullah,et al.  Catalyst development for the gasification of biomass in the dual-bed gasifier , 2003 .

[109]  Bo Xiao,et al.  A novel biomass pulverization technology , 2011 .

[110]  Anh N. Phan,et al.  Mathematical modelling of slow pyrolysis of segregated solid wastes in a packed-bed pyrolyser , 2007 .

[111]  Electo Eduardo Silva Lora,et al.  Syngas production in downdraft biomass gasifiers and its application using internal combustion engines , 2012 .

[112]  Yi Wang,et al.  Catalytic reforming of tar during gasification. Part III. Effects of feedstock on tar reforming using ilmenite as a catalyst , 2013 .

[113]  Jagtar Singh,et al.  A mathematical model for transporting the biomass to biomass based power plant. , 2010 .

[114]  T. A. Milne,et al.  Biomass Gasifier "Tars": Their Nature, Formation, and Conversion , 1998 .

[115]  Magnus Ståhl,et al.  Industrial processes for biomass drying and their effects on the quality properties of wood pellets , 2004 .

[116]  Giacobbe Braccio,et al.  Electricity production by biomass steam gasification using a high efficiency technology and low environmental impact , 2013 .

[117]  Hans Ivar Skjelbred,et al.  Linear mixed-integer models for biomass supply chains with transport, storage and processing , 2010 .

[118]  Mohammad Asadullah,et al.  Biomass Gasification to Hydrogen and Syngas at Low Temperature: Novel Catalytic System Using Fluidized-Bed Reactor , 2002 .

[119]  L. S. Esteban,et al.  Biomass resources and costs: Assessment in different EU countries , 2011 .

[120]  S. Karellas,et al.  Tar analysis from biomass gasification by means of online fluorescence spectroscopy , 2011 .

[121]  Tong Seop Kim,et al.  Effects of syngas type on the operation and performance of a gas turbine in integrated gasification combined cycle , 2011 .

[122]  Z. Zainal,et al.  Gasification of palm empty fruit bunch in a bubbling fluidized bed: a performance and agglomeration study. , 2011, Bioresource technology.

[123]  Mohammad Asadullah,et al.  Catalytic reforming of tar during gasification. Part I. Steam reforming of biomass tar using ilmenite as a catalyst , 2011 .