Surface Finish Improvement of Additive Manufactured Metal Parts

Unlike materials subtractive technologies, additive manufacturing (AM) works on producing near-net-shape components according to a specific design at which the synthesis is achieved layer by layer. Additive manufacturing allows design freedom, making design-driven manufacturing a reality. However, its poor surface quality is considered as one of the key challenges that are worth to overcome. The main objective of this chapter is to report a comprehensive overview of the techniques used to improve the surface finish and their advancements of products made by metal additive manufacturing (AM) technologies and to highlight experimental processes and data. Powder bed fusion (PBF) and direct laser deposition (DLD) are the main processes covered in this review. The chapter starts with the literature review and introduction to the main metal AM processes and their surface roughness limitations, the effect of their parameters and the effect of the laser re-melting on the surface quality. Next, it is followed by a number of surface finishing techniques such as laser polishing, chemical and electropolishing. Experimental results of post-surface finishing of AM parts by microelectrical discharge machining are also presented.

[1]  T. Masuzawa,et al.  Micro-EDM for Three-Dimensional Cavities - Development of Uniform Wear Method - , 1998 .

[2]  Noboru Kikuchi,et al.  Closed loop direct metal deposition : art to part , 2000 .

[3]  U. Wendt,et al.  Laser alloying of aluminum with titanium wire , 2003 .

[4]  Pulak M. Pandey,et al.  Statistical modelling and optimization of surface roughness in the selective laser sintering process , 2007 .

[5]  Liang Hao,et al.  Surface finish improvement of LMD samples using laser polishing , 2010 .

[6]  Joaquim Ciurana,et al.  Influence of process parameters on part quality and mechanical properties for DMLS and SLM with iron-based materials , 2012 .

[7]  L. Murr,et al.  Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies , 2012 .

[8]  Martine Wevers,et al.  Surface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing , 2012 .

[9]  Anders Snis,et al.  Effect of process parameters settings and thickness on surface roughness of EBM produced Ti‐6Al‐4V , 2012 .

[10]  H. Liao,et al.  Morphology evolution mechanism of single tracks of FeAl intermetallics in selective laser melting , 2012 .

[11]  Konrad Wegener,et al.  Super-finished surfaces using meso-micro EDM , 2013 .

[12]  Remy Fabbro,et al.  Influence of various process conditions on surface finishes induced by the direct metal deposition laser technique on a Ti-6Al-4V alloy , 2013 .

[13]  Christoph Leyens,et al.  Generative Manufacturing and Repair of Metal Parts through Direct Laser Deposition Using Wire Material , 2013, NEW PROLAMAT.

[14]  F. Calignano,et al.  Influence of process parameters on surface roughness of aluminum parts produced by DMLS , 2012, The International Journal of Advanced Manufacturing Technology.

[15]  William E. Frazier,et al.  Metal Additive Manufacturing: A Review , 2014, Journal of Materials Engineering and Performance.

[16]  Joakim Karlsson,et al.  Thickness dependency of mechanical properties for thin-walled titanium parts manufactured by Electron Beam Melting (EBM®) , 2016 .

[17]  Moataz M. Attallah,et al.  The influence of the laser scan strategy on grain structure and cracking behaviour in SLM powder-bed fabricated nickel superalloy , 2014 .

[18]  D. I. Wimpenny,et al.  On Optimization of Surface Roughness of Selective Laser Melted Stainless Steel Parts: A Statistical Study , 2014, Journal of Materials Engineering and Performance.

[19]  Chin-Ching Yeh.  Trend Analysis for the Market and Application Development of 3D Printing , 2014 .

[20]  E. Chlebus,et al.  Chemical polishing of scaffolds made of Ti–6Al–7Nb alloy by additive manufacturing , 2014 .

[21]  O. Remus Tutunea-Fatan,et al.  Performance of laser polishing in finishing of metallic surfaces , 2014, The International Journal of Advanced Manufacturing Technology.

[22]  C. Wen,et al.  Dynamic behaviour of high strength steel parts developed through laser assisted direct metal deposition , 2014 .

[23]  Frédéric Thiesse,et al.  Shapeways and the 3D Printing Revolution , 2014, ECIS.

[24]  Chor Yen Yap,et al.  Review of selective laser melting : materials and applications , 2015 .

[25]  Zengxi Pan,et al.  Wire-feed additive manufacturing of metal components: technologies, developments and future interests , 2015 .

[26]  E. O. Olakanmi,et al.  A review on selective laser sintering/melting (SLS/SLM) of aluminium alloy powders: Processing, microstructure, and properties , 2015 .

[27]  N. Shamsaei,et al.  An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control , 2015 .

[28]  Jean-Yves Hascoët,et al.  Laser polishing of additive laser manufacturing surfaces , 2015 .

[29]  Moataz M. Attallah,et al.  In-situ shelling via selective laser melting: Modelling and microstructural characterisation , 2015 .

[30]  Radovan Kovacevic,et al.  The influence of heat accumulation on the surface roughness in powder-bed additive manufacturing , 2015 .

[31]  Bijoy Bhattacharyya,et al.  Study on the influence of micro-EDM process parameters during machining of Ti–6Al–4V superalloy , 2015 .

[32]  Philip J. Withers,et al.  Influence of processing conditions on strut structure and compressive properties of cellular lattice structures fabricated by selective laser melting , 2015 .

[33]  D. I. Wimpenny,et al.  Laser polishing of selective laser melted components , 2015 .

[34]  P. Wanjara,et al.  FIBER LASER DEPOSITION OF NICKEL-BASED SUPERALLOYS USING FILLER WIRE FEED , 2015 .

[35]  D. Kotoban,et al.  Comparative Study of Selective Laser Melting and Direct Laser Metal Deposition of Ni3Al Intermetallic Alloy , 2015 .

[36]  John J. Lewandowski,et al.  Overview of Materials Qualification Needs for Metal Additive Manufacturing , 2016 .

[37]  R. Keshavamurthy,et al.  A novel technique for reducing lead-time and energy consumption in fabrication of Inconel-625 parts by laser-based metal deposition process , 2016 .

[38]  C. Körner,et al.  Additive manufacturing of metallic components by selective electron beam melting — a review , 2016 .

[39]  Moataz M. Attallah,et al.  Adding functionality with additive manufacturing: Fabrication of titanium-based antibiotic eluting implants. , 2016, Materials science & engineering. C, Materials for biological applications.

[40]  Lars-Erik Rännar,et al.  The effect of EBM process parameters upon surface roughness , 2016 .

[41]  Albert Folch,et al.  The upcoming 3D-printing revolution in microfluidics. , 2016, Lab on a chip.

[42]  P. Lykov,et al.  Influence of SLM Process Parameters on Porosity of Nickel Base Heat Resistance Alloy EP648 , 2016 .

[43]  Robert F. Singer,et al.  Microstructure of the Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting , 2016, Metallurgical and Materials Transactions A.

[44]  D. Gu,et al.  Selective Laser Melting Additive Manufacturing of Hard-to-Process Tungsten-Based Alloy Parts With Novel Crystalline Growth Morphology and Enhanced Performance , 2016 .

[45]  J. Eckert,et al.  Selective laser melting of ultra-high-strength TRIP steel: processing, microstructure, and properties , 2017, Journal of Materials Science.

[46]  J. Lin,et al.  Influence of laser beam fluence on surface quality, microstructure, mechanical properties, and tribological results for laser polishing of SKD61 tool steel , 2016 .

[47]  D. Wimpenny,et al.  Electropolishing of Re-melted SLM Stainless Steel 316L Parts Using Deep Eutectic Solvents: 3 × 3 Full Factorial Design , 2016, Journal of Materials Engineering and Performance.

[48]  Properties of Aluminium Alloys Produced by Selective Laser Melting , 2016 .

[49]  F. Liou,et al.  Blown powder deposition of 4047 aluminum on 2024 aluminum substrates , 2016 .

[50]  H. Riegel,et al.  Laser Polishing of Additive Manufactured AlSi10Mg Parts with an Oscillating Laser Beam , 2016 .

[51]  Angela Daly,et al.  Socio-Legal Aspects of the 3D Printing Revolution , 2016 .

[52]  M. Kottman,et al.  Experimental study and modeling of H13 steel deposition using laser hot-wire additive manufacturing , 2016 .

[53]  V G Smelov,et al.  Selective laser melting of titanium alloy: investigation of mechanical properties and microstructure , 2016 .

[54]  I. Fassi,et al.  A New Process Combining Micro-Electro-Discharge-Machining Milling and Sinking for Fast Fabrication of Microchannels With Draft Angle , 2016 .

[55]  Sheng Li,et al.  The development of TiNi-based negative Poisson's ratio structure using selective laser melting , 2016 .

[56]  Andrey Koptyug,et al.  Additive manufacturing of 316L stainless steel by electron beam melting for nuclear fusion applications , 2017 .

[57]  Wei Zhou,et al.  Laser polishing of additive manufactured Ti alloys , 2017 .

[58]  D. Clark,et al.  Microstructural characterisation of a nickel alloy processed via blown powder direct laser deposition (DLD) , 2017 .

[59]  N. Hrabe,et al.  Fatigue properties of a titanium alloy (Ti–6Al–4V) fabricated via electron beam melting (EBM): Effects of internal defects and residual stress , 2017 .

[60]  R. Boardman,et al.  Investigation on Porosity and Microhardness of 316L Stainless Steel Fabricated by Selective Laser Melting , 2017 .

[61]  H. Riegel,et al.  Laser polishing of ground aluminum surfaces with high continuous wave laser , 2017 .

[62]  S. Zaharia,et al.  Microstructure and micro-hardness analyses of titanium alloy Ti-6Al-4V parts manufactured by selective laser melting , 2017 .

[63]  Afif Batal,et al.  Laser polishing of 3D printed mesoscale components , 2017 .