Simulation and optimization of waste heat recovery in sinter cooling process

Abstract The particle size, the gaseous velocity and temperature at the inlet, and the porosity and the height of the sintered bed are the five main parameters affecting the efficiency of the waste heat recovery in a sinter cooling process. A numerical model was developed on the basis of the porous media model and local non-equilibrium thermodynamics model, to reveal the flow and heat transfer characteristics of a 420 m2 sinter cooler in an iron and steel company with the software package Fluent 6.3. Simulation was carried out and influences of different parameters on the distribution of solid temperature, the gaseous temperature and velocity, and the waste heat utilization were discussed. The reliability of this model was verified by comparing the prediction data with the experimental data. In order to investigate the influence of multi-layer feeding on waste heat utilization, 10 parameters including the above five were optimized with the mixed orthogonal experimental method. The significance degree of the parameters was obtained. The optimal combination of the parameters was proposed in the purpose of improving the waste heat utilization. The amount of waste heat utilization is 2.5531 × 108 kJ/h in the optimal condition, which increases 26.26% compared to the standard condition.

[1]  Weng Shi-lie.  The Latest Research Findings Concerning Low-temperature Heat Energy-based Power Generation and its Development Trend , 2007 .

[2]  Jiin-Yuh Jang,et al.  3-D Transient conjugated heat transfer and fluid flow analysis for the cooling process of sintered bed , 2009 .

[3]  Won Kook Lee,et al.  Fixed-bed adsorption for bulk component system. Non-equilibrium, non-isothermal and non-adiabatic model , 1995 .

[4]  Antonio Casimiro Caputo,et al.  Heat Recovery from Moving Cooling Beds: Transient Modeling by Dynamic Simulation , 1999 .

[5]  A. Lozano Martínez-Luengas,et al.  A study of the collapse of a WWII communications antenna using numerical simulations based on design of experiments by FEM , 2010 .

[6]  Junya Kano,et al.  Numerical simulation model of the iron ore sintering process directly describing the agglomeration phenomenon of granules in the packed bed , 2000 .

[7]  Rosemary Norman,et al.  Low grade thermal energy sources and uses from the process industry in the UK , 2012 .

[8]  Antonio Casimiro Caputo,et al.  Comparing heat recovery schemes in solid bed cooling , 1997 .

[9]  Xie Dong-jiang.  Optimal Orthogonal Simulation Research of Sinter Cooling , 2011 .

[10]  Shigeki Toyama,et al.  Heat transfer and fluid flow analysis of sinter coolers with consideration of size segregation and initial temperature distribution. , 1988 .

[11]  Antonio Casimiro Caputo,et al.  Analysis of heat recovery in gas-solid moving beds using a simulation approach , 1996 .

[12]  S. Ergun.  Fluid flow through packed columns , 1952 .

[13]  Kambiz Vafai,et al.  Analysis of fluid flow and heat transfer interfacial conditions between a porous medium and a fluid layer , 2001 .

[14]  Jiang Tao,et al.  Fuel appropriate distribution in iron ore sintering , 2006 .

[15]  Chang-Hsien Tai,et al.  Effect of sinter layer porosity distribution on flow and temperature fields in a sinter cooler , 2009 .

[16]  Antonio Casimiro Caputo,et al.  Optimization criteria of heat recovery from solid beds , 1997 .

[17]  Yasser Mahmoudi,et al.  Analytical investigation of heat transfer enhancement in a channel partially filled with a porous material under local thermal non-equilibrium condition , 2011 .

[18]  Antonio Casimiro Caputo,et al.  Fuzzy control of heat recovery systems from solid bed cooling , 2000 .

[19]  G. Bisio,et al.  Energy recovery from molten slag and exploitation of the recovered energy , 1997 .

[20]  Xie Dongjiang.  Optimization and simulation of sinter cooling process , 2011 .