Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion

Abstract The technology of 3D Concrete Printing (3DCP) has progressed rapidly over the last years. With the aim to realize both buildings and civil works, the need for reliable mechanical properties of printed concrete grows. As a consequence of the additive manufacturing technique, 3D printed structures may consist of several layers that should exhibit bond to guarantee a safe structural design. This paper presents the results of an experimental study on the relation between the 3DCP process parameters and the bond strength of 3D printed concrete. The effect of 3 process parameters (interlayer interval time, nozzle height, and surface dehydration) on two mechanical properties (compressive strength and tensile strength, determined through flexural and splitting tests), has been established, in three perpendicular directions. A very limited influence of layer orientation was found for the given process-material combination, given a sufficiently short interlayer interval time. However, the bond strength between the layers reduced for increasing interlayer interval times. This was also reflected by the failure mode of the samples. The reduction in strength became more pronounced for the samples that were left uncovered during the interval time, exposed to drying. No clear relation was found between the height of the nozzle, and the bond strength between layers. The results of this study, in comparison to various other works on 3DCP, emphasize the need for standardization of test methods and characterization of 3D printed concrete, as individual process parameters clearly must be considered in relation to the applied material and other process parameters.

[1]  Z. Ahmed,et al.  Design of a 3D printed concrete bridge by testing , 2018, Virtual and Physical Prototyping.

[2]  Nathalie Labonnote,et al.  Additive construction: State-of-the-art, challenges and opportunities , 2016 .

[3]  Robert J. Flatt,et al.  Chloride Ingress Through Cold Joints in Digitally Fabricated Concrete by micro-XRF Mapping , 2018 .

[4]  Gert Heshe,et al.  DS/ENV 1992-1-1 NAD. National Application Document for Eurocode 2: Design of Concrete Structures, Part 1-1: General Rules and Rules for Buildings , 1993 .

[5]  Joseph J. Assaad,et al.  Correlating Thixotropy of Self-Consolidating Concrete to Stability, Formwork Pressure, and Multilayer Casting , 2016 .

[6]  Jay G. Sanjayan,et al.  Effect of Delay Time on the Mechanical Properties of Extrusion-Based 3D Printed Concrete , 2017 .

[7]  WooSeok Kim,et al.  Evaluation of Shear Strength of RC Beams with Multiple Interfaces Formed before Initial Setting Using 3D Printing Technology , 2017, Materials.

[8]  B. Panda,et al.  Measurement of tensile bond strength of 3D printed geopolymer mortar , 2018 .

[9]  Kamal H. Khayat,et al.  Bond Strength in Multilayer Casting of Self-Consolidating Concrete , 2017 .

[10]  Konrad Zilch,et al.  Capacity of Shear Joints in Applications of High Performance Concrete in Strengthening and Retrofitting of old Concrete Structures , 2002 .

[11]  Xiong Guang-jing,et al.  Microstructure model of the interfacial zone between fresh and old concrete , 2002 .

[12]  Philippe Coussot,et al.  Quantification de la thixotropie des matériaux cimentaires et de ses effet , 2006 .

[13]  K. Van Tittelboom,et al.  The effect of print parameters on the (Micro) structure of 3D printed cementitious materials , 2018 .

[14]  Freek Bos,et al.  Correlation between destructive compression tests and non-destructive ultrasonic measurements on early age 3D printed concrete , 2018, Construction and Building Materials.

[15]  Nicolas Roussel,et al.  Weak bond strength between successive layers in extrusion-based additive manufacturing: measurement and physical origin , 2019, Cement and Concrete Research.

[16]  Ming Jen Tan,et al.  Fresh and hardened properties of 3D printable cementitious materials for building and construction , 2018 .

[17]  Viktor Mechtcherine,et al.  Studying the Printability of Fresh Concrete for Formwork-Free Concrete Onsite 3D Printing Technology (CONPrint3D) , 2019, 3D Concrete Printing Technology.

[18]  Valentín.  Chapter 4. , 1998, Annals of the ICRP.

[19]  Behrokh Khoshnevis,et al.  Interlayer adhesion and strength of structures in Contour Crafting - Effects of aggregate size, extrusion rate, and layer thickness , 2017 .

[20]  Freek Bos,et al.  Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing , 2018 .

[21]  Ming Jen Tan,et al.  Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material , 2017 .

[22]  Csaba Simon,et al.  Experimental Investigations on Upgrading Structures with High Strength Concrete Overlay , 2013 .

[23]  Pedro Santos,et al.  Assessment of shear strength between concrete layers , 2009 .

[24]  Richard A. Buswell,et al.  3D printing using concrete extrusion: A roadmap for research , 2018, Cement and Concrete Research.

[25]  Freek Bos,et al.  Additive manufacturing of concrete in construction: potentials and challenges of 3D concrete printing , 2016, International Journal of Civil Engineering and Construction.

[26]  Viktor Mechtcherine,et al.  Capillary Water Intake by 3D-Printed Concrete Visualised and Quantified by Neutron Radiography , 2018, RILEM Bookseries.

[27]  Jian fei Chen,et al.  Mechanical Properties of Structures 3D-Printed With Cementitious Powders , 2015, 3D Concrete Printing Technology.

[28]  A. Gibb,et al.  Hardened properties of high-performance printing concrete , 2012 .

[29]  N. Roussel,et al.  Distinct-layer casting of SCC: The mechanical consequences of thixotropy , 2008 .