Charge amplifier Design Methodology for PVDF-Based Tactile Sensors

This paper proposes and describes a charge amplifier-based interface electronics design methodology approach for piezoelectric polymer tactile sensors to be used for humanoid robot applications. The tactile sensor–consisting of a PVDF single sensor element–is illustrated, the electromechanical thickness mode behavior is modeled and a fabricated prototype is presented. The model allows associating the PVDF charge response to the effective load applied on the outer surface of the sensor. The model is also used as a key in the proposed design methodology to estimate the charge to be detected by the charge amplifier. A case study based on the design methodology approach is reported. The system (PVDF single taxel + interface electronics) is analyzed firstly, considering it as ideal and then when the nonidealities come into play. A charge amplifier-based interface electronics prototype is also presented. The implementation is used to validate the followed approach and then defining the design specs towards the dedicated IC design. Some experimental results are also reported.

[1]  Maurizio Valle,et al.  POSFET Based Tactile Sensor Arrays , 2007, 2007 14th IEEE International Conference on Electronics, Circuits and Systems.

[2]  Peng Li,et al.  A Low-Power 12-Bit 250 KS/S Cyclic ADC for Long Line Array Infrared Sensors readout Circuit , 2011, J. Circuits Syst. Comput..

[3]  Andrew Berry,et al.  A CMOS analog integrated circuit for pixel X-Ray detector , 2009, Proceedings of the 2009 12th International Symposium on Integrated Circuits.

[4]  A. Loi,et al.  Piezoelectric polymer transducer arrays for flexible tactile sensors , 2012, 2012 IEEE Sensors.

[5]  H. Worn,et al.  Resistive tactile sensor matrices using inter-electrode sampling , 2005, 31st Annual Conference of IEEE Industrial Electronics Society, 2005. IECON 2005..

[6]  Guo-Neng Lu,et al.  A charge-sensitive amplifier associated with APD or PMT for 511 keV, photon-pair detection , 2010 .

[7]  Cheng-Hsin Chuang,et al.  Flexible Piezoelectric Tactile Sensors with Structural Electrodes Array , 2009 .

[8]  Rocco Vertechy,et al.  Smart Actuation and Sensing Systems - Recent Advances and Future Challenges , 2012 .

[9]  Hyung-Kew Lee,et al.  A Flexible Polymer Tactile Sensor: Fabrication and Modular Expandability for Large Area Deployment , 2006, Journal of Microelectromechanical Systems.

[10]  Michael S. Shur,et al.  SPECIAL ISSUE ON SENSITIVE SKIN , 2000 .

[11]  Giulio Sandini,et al.  An embedded artificial skin for humanoid robots , 2008, 2008 IEEE International Conference on Multisensor Fusion and Integration for Intelligent Systems.

[12]  Mark D. Semon,et al.  POSTUSE REVIEW: An Introduction to Error Analysis: The Study of Uncertainties in Physical Measurements , 1982 .

[13]  Maurizio Valle,et al.  Interface electronics for tactile sensing arrays , 2011, 2011 18th IEEE International Conference on Electronics, Circuits, and Systems.

[14]  Albert H. Titus,et al.  Towards an autonomous integrated sensor system , 2009 .

[15]  Armin Tajalli,et al.  Implementing Ultra-high-Value Floating Tunable CMOS Resistors , 2008 .

[16]  E. R. Cohen.  An Introduction to Error Analysis: The Study of Uncertainties in Physical Measurements , 1998 .

[17]  Giorgio Metta,et al.  Methods and Technologies for the Implementation of Large-Scale Robot Tactile Sensors , 2011, IEEE Transactions on Robotics.

[18]  G. De Robertis,et al.  GASTONE: A new ASIC for the cylindrical GEM inner tracker of KLOE experiment at DAFNE , 2009 .

[19]  Pasqualina M. Sarro,et al.  A silicon MEMS structure for characterization of femto-farad-level capacitive sensors with lock-in architecture , 2010 .