Effect of WC mass fraction on the microstructure and frictional wear properties of WC/Fe matrix composites

[1]  Jianbo Lei,et al.  Effects of WC particles on microstructure and mechanical properties of 316L steel obtained by laser melting deposition , 2022, Ceramics International.

[2]  Yunhua Xu,et al.  The investigation on the fabrication and microstructure of a novel core-shell structure reinforced iron matrix composite , 2021, Vacuum.

[3]  T. Murthy,et al.  The studies on the tribological performance, characterization and mechanical properties of W-2Ni-1Fe (wt%) alloy , 2021, International Journal of Refractory Metals and Hard Materials.

[4]  Yunhua Xu,et al.  Room-temperature wear resistance of tungsten carbide composite layers produced on grey cast iron by diffusion-controlled in situ reactions , 2021 .

[5]  O. Anderoglu,et al.  Microstructures and properties of Ti/TiC composites fabricated by laser-directed energy deposition , 2021 .

[6]  K. Shimizu,et al.  Effect of Carbon Content on Three-body Abrasive Wear Characteristics of 28Cr-3Ni Cast Alloys , 2021, ISIJ International.

[7]  Shuliang Zou,et al.  Influences of arc current on microstructure of Cr coating for Zr-4 alloy prepared by multi-arc ion plating via EBSD , 2021 .

[8]  Zhong Chen,et al.  Microstructure and wear characteristics of in-situ micro/nanoscale niobium carbide reinforced copper composites fabricated through powder metallurgy , 2021 .

[9]  M. Mohammadi,et al.  Plastic deformation throughout strain-induced phase transformation in additively manufactured maraging steels , 2021, Materials & Design.

[10]  Chao Zhang,et al.  Wear mechanism of Cu-based brake pad for high-speed train braking at speed of 380 km/h , 2020 .

[11]  M. Kamaya,et al.  A round robin EBSD measurement for quantitative assessment of small plastic strain , 2020 .

[12]  Yunhua Xu,et al.  Characterization of iron-based surface multilayer-structured tungsten carbide composite layers by EBSD and FIB/TEM , 2020 .

[13]  Yi Feng,et al.  Effect of electrical current density, apparent contact pressure, and sliding velocity on the electrical sliding wear behavior of Cu–Ti3AlC2 composites , 2020 .

[14]  Yang Li,et al.  Microstructure and wear properties of SiC woodceramics reinforced high-chromium cast iron , 2020 .

[15]  Xinfang Zhang,et al.  Fabrication of titanium carbide-reinforced iron matrix composites using electropulsing-assisted flash sintering , 2019 .

[16]  H. Liao,et al.  Additive manufacturing of WC reinforced maraging steel 300 composites by cold spraying and selective laser melting , 2019, Surface and Coatings Technology.

[17]  Q. B. Nguyen,et al.  High mechanical strengths and ductility of stainless steel 304L fabricated using selective laser melting , 2019, Journal of Materials Science & Technology.

[18]  S. Bhero,et al.  The influence of titanium addition on wettability of high-chromium white cast iron-matrix composites , 2018, Journal of Composite Materials.

[19]  Xiaozhou Liao,et al.  Hierarchical microstructure and strengthening mechanisms of a CoCrFeNiMn high entropy alloy additively manufactured by selective laser melting , 2018, Scripta Materialia.

[20]  H. Liao,et al.  Selective laser melting of tungsten carbide reinforced maraging steel composite , 2018, Additive Manufacturing.

[21]  D. Grzesiak,et al.  Strengthening of stainless steel by titanium carbide addition and grain refinement during selective laser melting , 2018 .

[22]  D. Yi,et al.  Improving the mechanical properties of tantalum carbide particle-reinforced iron-based composite by varying the TaC contents , 2017 .

[23]  K. Gao,et al.  The effect of volume fraction of WC particles on wear behavior of in-situ WC/Fe composites by spark plasma sintering , 2017 .

[24]  Yunhua Xu,et al.  Fe–W–C thermodynamics and in situ preparation of tungsten carbide-reinforced iron-based surface composites by solid-phase diffusion , 2016 .

[25]  M. Tarcolea,et al.  The effect of TiSiN interlayers on the bond strength of ceramic to NiCr and CoCr alloys , 2015 .

[26]  C. Desrayaud,et al.  Effect of Ca-addition on dynamic recrystallization of Mg–Zn alloy during hot deformation , 2013 .

[27]  André McDonald,et al.  Effect of reinforcing particles on the wear rate of low-pressure cold-sprayed WC-based MMC coatings , 2013 .

[28]  A. Senos,et al.  Cemented carbide phase diagrams: A review , 2011 .

[29]  Wen Ge Li,et al.  Laser Cladding In Situ Tungsten Carbide Reinforced Ferrous Matrix Surface Composites , 2011 .

[30]  Wilhelm Meiners,et al.  Microstructure characteristics and formation mechanisms of in situ WC cemented carbide based hardmetals prepared by Selective Laser Melting , 2010 .

[31]  Yunhua Xu,et al.  Preparation of in situ-formed WC/Fe composite on gray cast iron substrate by a centrifugal casting process , 2010 .

[32]  Christopher A. Schuh,et al.  Sliding wear of nanocrystalline Ni-W: Structural evolution and the apparent breakdown of Archard scaling , 2010 .

[33]  A. L. Ivanovskii,et al.  Structural, electronic and magnetic properties of η carbides (Fe3W3C, Fe6W6C, Co3W3C and Co6W6C) from first principles calculations , 2009, 0903.5390.

[34]  Xiaoyan Zeng,et al.  A study of Ni-based WC composite coatings by laser induction hybrid rapid cladding with elliptical spot , 2008 .

[35]  P. Tsakiropoulos,et al.  Solidification of high-Cr white cast iron–WC particle reinforced composites , 2005 .

[36]  Zhencai Zhu,et al.  A comparative study on microstructure evolution and wear resistance of different-sized tungsten carbide modified Fe-based laser cladding coatings , 2022, Optics & Laser Technology.

[37]  S. Zhang,et al.  Effect of Cr 3 C 2 content on 316L stainless steel fabricated by laser melting deposition , 2018 .