Thermal analysis of a conceptual loop heat pipe for solar central receivers

Abstract This study presents a novel loop heat pipe central receiver for the solar power tower (SPT) plant. For the first study, the evaporator section of the proposed receiver is simulated by a three-dimensional numerical model to study the flow, heat transfer and the evaporation phenomenon of the working fluid. In addition, effects of the outlet boundary pressure at the vapor groove and the solar irradiation heat flux on the absorbing surface are analyzed. The results show that most of the working fluid vaporizes at the liquid/vapor interface close to the casing. The heat transferred from the casing to the vapor working fluid is negligible, and thus the vapor temperature in the groove can be assumed to be constant in simulating the whole loop heat pipe central receiver. A lower temperature difference between the liquid/vapor interface and the compensation chamber is beneficial for obtaining more heat energy transferred to the vapor working fluid. It is also found that the evaporation heat transfer coefficient changes obviously with the absorbed solar heat flux. The findings of present work can be used as a reference to the modelling and design of the whole loop heat pipe central receiver in the next step.

[1]  G. P. Peterson,et al.  3D heat transfer analysis in a loop heat pipe evaporator with a fully saturated wick , 2011 .

[2]  E. Næss,et al.  Analysis of a Vertical Flat Heat Pipe Using Potassium Working Fluid and a Wick of Compressed Nickel Foam , 2016 .

[3]  P. Peterson,et al.  High-Temperature Liquid-Fluoride-Salt Closed-Brayton-Cycle Solar Power Towers , 2007 .

[4]  Guiping Lin,et al.  Modeling and analysis of startup of a loop heat pipe , 2010 .

[5]  Amir Faghri,et al.  Heat Pipe Science And Technology , 1995 .

[6]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[7]  P. Dutta,et al.  Evaporation Heat Transfer Coefficient in a Capillary Pumped Loop and Loop Heat Pipe for Different Working Fluids , 2012 .

[8]  F. Bai,et al.  Experimental Study of a Single Quartz Tube Solid Particle Air Receiver , 2015 .

[9]  Amir Faghri,et al.  Thermal analysis of a heat pipe solar central receiver for concentrated solar power tower , 2016 .

[10]  H. Nagano,et al.  Parametric Experiments on A Miniature Loop Heat Pipe with PTFE Wicks , 2014, SSRN Electronic Journal.

[11]  Amir Faghri,et al.  HEAT PIPES: REVIEW, OPPORTUNITIES AND CHALLENGES , 2014 .

[12]  J. Coventry,et al.  A review of sodium receiver technologies for central receiver solar power plants , 2015 .

[13]  Brian D. Iverson,et al.  Review of high-temperature central receiver designs for concentrating solar power , 2014 .

[14]  Peiwen Li,et al.  Thermal and Transport Properties of NaCl–KCl–ZnCl2 Eutectic Salts for New Generation High-Temperature Heat-Transfer Fluids , 2016 .

[15]  Kun Wang,et al.  Thermodynamic analysis and comparison for different direct-heated supercritical CO2 Brayton cycles integrated into a solar thermal power tower system , 2017 .

[16]  A. Faghri,et al.  Analysis of Porous Wick Heat Pipes, Including Capillary Dry-Out Limitations , 2005 .

[17]  Yu.F. Maydanik,et al.  Loop heat pipes , 2005 .

[18]  Walter B. Bienert.  The heat pipe and its application to solar receivers , 1980 .

[19]  Matteo Chiesa,et al.  Performance of a 100 kWth Concentrated Solar Beam-Down Optical Experiment , 2014 .

[20]  John Goldak,et al.  Numerical analysis of heat and mass transfer in the capillary structure of a loop heat pipe , 2006 .

[21]  T. L. Bergman,et al.  High temperature latent heat thermal energy storage using heat pipes , 2010 .

[22]  Ralf Uhlig,et al.  Conceptual study of central receiver systems with liquid metals as efficient heat transfer fluids , 2015 .

[23]  Tadej Semenic,et al.  Experimental study of biporous wicks for high heat flux applications , 2009 .

[24]  Nathan P. Siegel,et al.  Development and Evaluation of a Prototype Solid Particle Receiver: On-Sun Testing and Model Validation , 2010 .

[25]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[26]  Jocelyn Bonjour,et al.  Parametric analysis of loop heat pipe operation: a literature review , 2007 .

[27]  Antonio L. Avila-Marin,et al.  Volumetric receivers in Solar Thermal Power Plants with Central Receiver System technology: A review , 2011 .

[28]  A. Kribus,et al.  Performance of the Directly-Irradiated Annular Pressurized Receiver (DIAPR) Operating at 20 Bar and 1,200°C , 2001 .

[29]  Yiding Cao,et al.  Conjugate analysis of a flat-plate type evaporator for capillary pumped loops with three-dimensional vapor flow in the groove , 1994 .

[30]  Xiaogang Jin,et al.  Experimental investigate on thermal properties of a novel high temperature flat heat pipe receiver in solar power tower plant , 2016 .

[31]  C. Ho.  Advances in central receivers for concentrating solar applications , 2017 .

[32]  Clifford K. Ho,et al.  High-Temperature Receiver Designs for Supercritical CO2 Closed-Loop Brayton Cycles , 2014 .

[33]  Frédéric Lefèvre,et al.  Literature review: Steady-state modelling of loop heat pipes , 2015 .

[34]  Yiding Cao.  Heat Pipe Solar Receivers for Concentrating Solar Power (CSP) Plants , 2013 .