Application of phase change materials to pre-heating of evaporator and pressure regulator of a gaseous sequential injection system

The vehicle engines having gaseous sequential injection systems of liquefied petroleum gas (LPG) are operated on gasoline until the engine coolant reaches the required temperature because the heat of the engine coolant passing through the evaporator and pressure regulator (E&PR) is not enough to vaporize the LPG that is at liquid phase. Therefore, the fuel economy and the decreasing pollutant emissions emitted to the environment through use of LPG cannot be completely achieved at cold start of the engines. In this study, an E&PR that can store thermal energy was designed by using of phase change material (PCM) in order to overcome cold start problem of E&PR in vehicles operated with LPG. The thermal behavior of the E&PR with PCM was determined at idle operating conditions and the effects of using the E&PR surrounded with PCM on exhaust emissions (HC, CO) were examined. It was observed from the study that the E&PR with PCM can solve the cold start problem of the LPG powered engines. The E&PR surrounded with PCM could start the engine with LPG after the 15h cooling period of the engine and LPG usage decreased HC and CO emissions by 17.32% and 28.71%, respectively.

[1]  Zhimin Liu,et al.  Real time NO emissions measurement during cold start in LPG SI engine , 2007 .

[2]  E. R. Jayaratne,et al.  Particle and carbon dioxide emissions from passenger vehicles operating on unleaded petrol and LPG fuel. , 2005, The Science of the total environment.

[3]  L. L. Vasiliev,et al.  Latent heat storage modules for preheating internal combustion engines: application to a bus petrol engine , 2000 .

[4]  Steven D. Burch,et al.  REDUCING COLD-START EMISSIONS BY CATALYTIC CONVERTER THERMAL MANAGEMENT. , 1995 .

[5]  Noriyuki Kishi,et al.  Technology for Reducing Exhaust Gas Emissions in Zero Level Emission Vehicles(ZLEV) , 1999 .

[6]  Hongwei Cui.  Exhaust Gas Recirculation Control in a Spark-Ignition LPG Engine Using Neural Networks , 2006, 2006 6th World Congress on Intelligent Control and Automation.

[7]  Simsoo Park,et al.  Experimental investigation on the time resolved THC emission characteristics of liquid phase LPG injection (LPLi) engine during cold start , 2007 .

[8]  Cha-Lee Myung,et al.  A combined experimental and computational approach to improve catalyst flow uniformity and light-off behaviour , 2002 .

[9]  T. F. Potter,et al.  Applications and benefits of catalytic converter thermal management , 1996 .

[10]  Arun S. Mujumdar,et al.  A parametric study of phase change material (PCM)-based heat sinks , 2008 .

[11]  Liguang Li,et al.  Cold start characteristics at low temperatures based on the first firing cycle in an LPG engine , 2007 .

[12]  Gerhart Eigenberger,et al.  Optimization of the cold-start behaviour of automotive catalysts using an electrically heated pre-catalyst , 1996 .

[13]  Metin Gumus,et al.  Reducing cold-start emission from internal combustion engines by means of thermal energy storage system , 2009 .

[14]  G. Wirmark,et al.  SULEV Emission Technologies for a Five Cylinder N/A Engine , 2000 .

[15]  Stephen George Russ,et al.  SI Engine Operation with Retarded Ignition: Part 1 - Cyclic Variations , 1999 .

[16]  N. Henein,et al.  Cold-start hydrocarbon emissions in port-injected gasoline engines , 1999 .

[17]  K Darkwa,et al.  Green transport technology (GTT): analytical studies of a thermochemical store for minimising energy consumption and air pollution from automobile engines , 1997 .

[18]  Isaac Schifter,et al.  Optimizing automotive LPG blend for Mexico City , 2000 .

[19]  P Blueher.  LATENTWAERMESPEICHER ERHOEHT DEN FAHRKOMFORT UND DIE FAHRSICHERHEIT , 1991 .

[20]  William C. Pfefferle,et al.  Development and Performance of Microlith™ Light-Off Preconverters for LEV/ULEV , 1997 .

[21]  Pantelis N. Botsaris,et al.  Emission reduction during cold start via catalyst surface control , 2004 .

[22]  P. M Golben,et al.  Hydride-based cold-start heater for automotive catalyst , 1997 .

[23]  Naeim A. Henein,et al.  Contribution of Cold and Hot Start Transients in Engine-out HC Emissions , 1998 .

[24]  Stephen George Russ,et al.  SI Engine Operation with Retarded Ignition: Part 2 -HC Emissions and Oxidation , 1999 .

[25]  G. Nagarajan,et al.  LPG fueled diesel engine using diethyl ether with exhaust gas recirculation , 2008 .

[26]  Achim Karl-Erich Heibel,et al.  Performance of Different Cell Structure Converters A Total Systems Perspective , 1998 .

[27]  C. Santanam,et al.  Design of a Dual Wall Air Gap Exhaust Manifold , 1998 .

[28]  Toru Kidokoro,et al.  Development of PZEV exhaust emission Control system , 2003 .

[29]  David K. Benson,et al.  Applications and benefits of catalytic converter thermal management , 1996 .

[30]  Karthik Ramanathan,et al.  Optimal design of catalytic converters for minimizing cold-start emissions , 2004 .

[31]  Piotr Bielaczyc,et al.  Cold Start Emissions Investigation at Different Ambient Temperature Conditions , 1998 .

[32]  S-J Jeong,et al.  A new strategy for improving the warm-up performance of a light-off auto-catalyst for reducing cold-start emissions , 2001 .

[33]  K. Kang,et al.  Effects of Injection Timing on Mixture Distribution in a Liquid-Phase LPG Injection Engine for a Heavy-Duty Vehicle , 2004 .

[34]  N. Collings,et al.  Time Resolved Measurement of Cold Start HC Concentration Using the Fast FID , 1996 .

[35]  E. Korin,et al.  Improving Cold-Start Functioning of Catalytic Converters by Using Phase-Change Materials , 1998 .

[36]  S. C. Solanki,et al.  Latent heat thermal energy storage using cylindrical capsule: Numerical and experimental investigations , 2006 .

[37]  J. Brown,et al.  Thermal management of high heat-flux sources using phase change materials - A design optimization procedure , 1997 .