R-curve behavior of SiN whisker-reinforced SiN matrix composites

Abstract Three kinds of β-Si 3 N 4 whisker-reinforced Si 3 N 4 composites with different degree of whisker alignment were prepared by using tape casting, extrusion and hot pressing processes. Among these composites, one is obtained from a laminate with tapes, another is from a laminate stacked alternatively with tapes and extruded wires, and the last one is closely stacked with wires. The same whisker orientation was followed with all the tapes or wires. Four-point bending tests by stepped loading were employed to determine R-curves for the three materials. The results show that all the materials have better R-curve behaviors than composites with randomly oriented whiskers. The fracture toughness of the three materials are, respectively, 11.18, 11.44 and 10.60 MPa m 1/2 , and the corresponding threshold values for stable crack propagation are 9.14, 10.92 and 9.32 MPa m 1/2 , respectively.

[1]  G. Messing,et al.  Fabrication of Oriented SiC‐Whisker‐Reinforced Mullite Matrix Composites by Tape Casting , 1994 .

[2]  Heon-Jin Choi,et al.  R‐Curve Behavior of Silicon Nitride–Titanium Nitride Composites , 2005 .

[3]  E. Fuller,et al.  Fracture Resistance Behavior of Silicon Carbide Whisker‐Reinforced Alumina Composites with Different Porosities , 1990 .

[4]  Dinesh K. Shetty,et al.  Rising Crack-Growth-Resistance (R-Curve) Behavior of Toughened Alumina and Silicon Nitride , 1991 .

[5]  A. Tsuge,et al.  Mechanical Properties of Unidirectionally Oriented SiC‐Whisker‐Reinforced Si3N4 Fabricated by Extrusion and Hot‐Pressing , 1993 .

[6]  S. Choi,et al.  Crack-Growth Resistance of in Situ-Toughened Silicon Nitride , 1994 .

[7]  James C. Newman,et al.  An empirical stress-intensity factor equation for the surface crack , 1981 .

[8]  R. Scattergood,et al.  Crack-shape effects for indentation fracture toughness measurements , 1992 .

[9]  B. Lawn,et al.  A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: II, Strength Method , 1981 .

[10]  Dong-Soo Park,et al.  Microstructure and mechanical properties of silicon nitride with tri-laminate structures , 2002 .

[11]  Dong-joo Lee,et al.  R‐Curve Behavior and Strength for In‐Situ Reinforced Silicon Nitrides with Different Microstructures , 1992 .

[12]  K. Ikeda,et al.  Effect of Surface Flaw Size on Fracture Strength of Alumina Ceramics , 1987 .

[13]  A. Evans,et al.  Elastic/Plastic Indentation Damage in Ceramics: The Median/Radial Crack System , 1980 .

[14]  R. Krause.  Rising Fracture Toughness from the Bending Strength of Indented Alumina Beams , 1988 .

[15]  D. K. Kim,et al.  Flaw‐Tolerance and R‐Curve Behavior of Liquid‐Phase‐Sintered Silicon Carbides with Different Microstructures , 1995 .

[16]  P. Becher.  Microstructural design of toughened ceramics , 1991 .

[17]  Masayoshi Ohashi,et al.  Processing Strategy for Producing Highly Anisotropic Silicon Nitride , 1995 .

[18]  R. Bradt,et al.  Fracture toughness testing of brittle materials , 1993 .

[19]  R. Drew,et al.  Microstructure of an Extruded β‐Silicon Nitride Whisker‐Reinforced Silicon Nitride Composite , 1992 .

[20]  Brian R. Lawn,et al.  A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: I , 1981 .

[21]  Dong-Soo Park,et al.  Orientation-dependent properties of silicon nitride with aligned reinforcing grains , 2000 .

[22]  S. Kanzaki,et al.  Fracture Resistance Behavior of Highly Anisotropic Silicon Nitride , 1995 .

[23]  Anthony G. Evans,et al.  Crack deflection processes—I. Theory , 1983 .