A comparison of cryogenic and high pressure emulsion cooling technologies on tool life and chip morphology in Ti-6Al-4V cutting

[1]  G. Thodos,et al.  Viscosity and Thermal Conductivity of Water: Gaseous and liquid States. , 1963 .

[2]  R. Tufeu,et al.  Thermal conductivity coefficients of water and heavy water in the liquid state up to 370.degree.C , 1976 .

[3]  E. M. Trent,et al.  Metal cutting and the tribology of seizure: I seizure in metal cutting , 1988 .

[4]  E. M. Trent.  Metal cutting and the tribology of seizure: II movement of work material over the tool in metal cutting , 1988 .

[5]  D. Friend,et al.  The thermal conductivity and heat capacity of fluid nitrogen , 1991 .

[6]  T. Kitagawa,et al.  Temperature and wear of cutting tools in high-speed machining of Inconel 718 and Ti6Al6V2Sn , 1997 .

[7]  Z. M. Wang,et al.  Titanium alloys and their machinability—a review , 1997 .

[8]  Shane Y. Hong,et al.  Cooling approaches and cutting temperatures in cryogenic machining of Ti-6Al-4V , 2001 .

[9]  Shane Y. Hong,et al.  New cooling approach and tool life improvement in cryogenic machining of titanium alloy Ti-6Al-4V , 2001 .

[10]  Álisson Rocha Machado,et al.  Cooling ability of cutting fluids and measurement of the chip‐tool interface temperatures , 2002 .

[11]  Emmanuel O. Ezugwu,et al.  High speed machining of aero-engine alloys , 2004 .

[12]  E. Lemmon,et al.  Viscosity and Thermal Conductivity Equations for Nitrogen, Oxygen, Argon, and Air , 2004 .

[13]  Martin Bäker,et al.  Mechanisms of Chip Formation , 2005 .

[14]  T. Childs,et al.  Friction modelling in metal cutting , 2006 .

[15]  Soumitra Paul,et al.  ENVIRONMENTALLY CONSCIOUS MACHINING AND GRINDING WITH CRYOGENIC COOLING , 2006 .

[16]  N. R. Dhar,et al.  Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition , 2007 .

[17]  A. B. Chattopadhyay,et al.  Tool wear in cryogenic turning of Ti-6Al-4V alloy , 2007 .

[18]  S. Paul,et al.  EFFECT OF COOLANT PRESSURE, NOZZLE DIAMETER, IMPINGEMENT ANGLE AND SPOT DISTANCE IN HIGH PRESSURE COOLING WITH NEAT OIL IN TURNING Ti-6AL-4V , 2008 .

[19]  S. Paul,et al.  Some studies on high-pressure cooling in turning of Ti–6Al–4V , 2009 .

[20]  Vishal S. Sharma,et al.  Cooling techniques for improved productivity in turning , 2009 .

[21]  S. Palanisamy,et al.  Effects of coolant pressure on chip formation while turning Ti6Al4V alloy , 2009 .

[22]  M. Dargusch,et al.  Characteristics of cutting forces and chip formation in machining of titanium alloys , 2009 .

[23]  M. Dargusch,et al.  Machining Ti–6Al–4V alloy with cryogenic compressed air cooling , 2010 .

[24]  Matthew S. Dargusch,et al.  New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V , 2011 .