Seismic Performance and Modeling of a Half-Scale Base-Isolated Wood Frame Building

The concept of base isolation is a century old, but application to civil engineering structures has only occurred over the last several decades. Application to light-frame wood buildings in North America has been virtually non existent with one notable exception. This article quantitatively examines issues associated with application of base isolation in light-frame wood building systems including: (1) constructability issues related to ensuring sufficient in-plane floor diaphragm stiffness to transfer shear from the superstructure to the isolation system; (2) evaluation of experimental seismic performance of a half-scale base-isolated light-frame wood building; and (3) development of a displacement–based seismic design method and numerical model and their comparison with experimental results. The results of the study demonstrate that friction pendulum system (FPS) bearings offer a technically viable passive seismic protection system for light-frame wood buildings in high seismic zones. Specifically, the amount and method of stiffening the floor diaphragm is not unreasonable, given that the inter-story drift and accelerations at the upper level of the tested building were very low, thus resulting in the expectation of virtually no structural, non structural, or contents damage in low-rise wood frame buildings. The nonlinear dynamic model was able to replicate both the isolation layer and superstructure movement with good accuracy. The displacement-based design method was proven to be a viable tool to estimate the inter-story drift of the superstructure. These tools further underscore the potential of applying base isolation systems for application to North America's largest building type.

[1]  Andre Filiatrault,et al.  Displacement-based seismic design of light-frame wood buildings , 2006 .

[2]  Shiling Pei,et al.  Performance-Based Shear Wall Design of Six-Story Neeswood Capstone Building via Simplified Direct Displacement Design Procedure , 2010 .

[3]  John W. van de Lindt,et al.  Development and Application of Wood Shear Wall Reliability Model , 2003 .

[4]  B. Taranath.  Seismic Rehabilitation of Existing Buildings , 2004 .

[5]  Mervyn J. Kowalsky,et al.  Displacement-based seismic design of structures , 2007 .

[6]  Shiling Pei,et al.  Methodology for earthquake-induced loss estimation: An application to woodframe buildings , 2009 .

[7]  Andre Filiatrault,et al.  Performance-Based Seismic Design of Wood Framed Buildings , 2002 .

[8]  J. W. van de Lindt,et al.  Energy-Based Similitude for Shake Table Testing of Scale Woodframe Structures , 2008 .

[9]  M. D. Symans,et al.  DISPLACEMENT-BASED DESIGN OF SEISMICALLY-ISOLATED WOODFRAMED STRUCTURES , 2010 .

[10]  Michael D. Symans,et al.  Base Isolation and Supplemental Damping Systems for Seismic Protection of Wood Structures: Literature Review , 2002 .

[11]  Juan Carlos de la Llera,et al.  Modelling aspects of structures isolated with the frictional pendulum system , 1998 .

[12]  John W. van de Lindt,et al.  Performance of a Woodframe Structure during Full-Scale Shake-Table Tests: Drift, Damage, and Effect of Partition Wall , 2007 .

[13]  John W. van de Lindt,et al.  Performance-Based Seismic Design of Wood Frame Buildings Using a Probabilistic System Identification Concept , 2008 .

[14]  Andrei M. Reinhorn,et al.  Teflon Bearings in Base Isolation II: Modeling , 1990 .

[15]  Bruce R. Ellingwood,et al.  Performance-Based Engineering of Wood Frame Housing: Fragility Analysis Methodology , 2002 .

[16]  Andrew S. Whittaker,et al.  Characterization and Modeling of Friction Pendulum Bearings Subjected to Multiple Components of Excitation , 2004 .

[17]  Donatello Cardone,et al.  Direct displacement-based design of seismically isolated bridges , 2009 .

[18]  Johannes Beck,et al.  Improving Loss Estimation for Woodframe Buildings , 2001 .