Influence of driving rain and vapour diffusion on the hygrothermal performance of a hygroscopic and permeable building envelope

Abstract Most natural building materials are hygroscopic and permeable to water vapour. These two characteristics have the potential to improve the longevity and indoor air quality of buildings. However, the potential of winter condensation due to vapour diffusion and the risk of mold growth should be assessed for safeguarding the longevity of building assemblies. This study investigates the relative importance of driving rain, plaster capillarity and the presence of a vapour barrier on the moisture content of building materials and the risk of mold growth for a hygroscopic and permeable building envelope (HPBE). Hygrothermal simulations of a single-family house in Denmark mainly made of wood and clay are performed with WUFI. Results indicate that the presence of an overhang is essential to ensure the durability of a HPBE rendered with a capillary active lime-based plaster while the presence of an overhang has a negligible impact for a mineral cement-based plaster. Including a vapour barrier did not introduce significant changes on the moisture content of this wall assembly. Simulation results indicate that the type of plaster and the wind-driven rain exposure are the most critical variables affecting the hygrothermal performance of this wall assembly.

[1]  C. Simonson,et al.  The effect of structures on indoor humidity--possibility to improve comfort and perceived air quality. , 2002, Indoor air.

[2]  Tim Padfield.  The role of absorbent building materials in moderating changes of relative humidity: Ph.D.thesis , 1999 .

[3]  Hua Ge,et al.  Effects of roof overhangs on wind-driven rain wetting of a low-rise cubic building: A numerical study , 2014 .

[4]  Uzzwal Kumar Deb Nath,et al.  Measurements of Wind-driven Rain on Mid- and High-rise Buildings in three Canadian Regions , 2015 .

[5]  T. Sterling,et al.  Indirect health effects of relative humidity in indoor environments. , 1986, Environmental health perspectives.

[6]  John Straube,et al.  Assessing the Durability Impacts of Energy Efficient Enclosure Upgrades Using Hygrothermal Modeling , 2006 .

[7]  Giuseppina Ciulla,et al.  An overview of energy retrofit actions feasibility on Italian historical buildings , 2017 .

[8]  John Straube,et al.  Ventilated Wall Claddings: Review, Field Performance, and Hygrothermal Modeling , 2009 .

[9]  Refrigerating.  ASHRAE handbook of fundamentals , 1967 .

[10]  Carey J. Simonson,et al.  Heat and Mass Transfer between Indoor Air and a Permeable and Hygroscopic Building Envelope: Part II – Verification and Numerical Studies , 2004 .

[11]  A. Evrard,et al.  Hygrothermal Performance of Lime-Hemp Wall Assemblies , 2010 .

[12]  F. Henriques,et al.  Influence of driving rain on the hygrothermal behavior of solid brick walls , 2016 .

[13]  Prabal Talukdar,et al.  Reliability of material data measurements for hygroscopic buffering , 2010 .

[14]  Ákos Lakatos,et al.  Analysis of the change of the specific heat loss coefficient of buildings resulted by the variation of the geometry and the moisture load , 2016 .

[15]  Joseph Lstiburek,et al.  Moisture Control for Buildings , 2002 .

[16]  D. Bastien,et al.  Permeable and Hygroscopic Building Envelopes: Hygrothermal Simulations of “Det Naturlige Hus” , 2017 .

[17]  J. Carmeliet,et al.  A review of wind-driven rain research in building science , 2004 .

[19]  C. Rode,et al.  Magnesium-oxide boards cause moisture damage inside facades in new Danish buildings , 2016 .

[20]  Ralf Klein,et al.  Hygrothermal risks of using exterior air barrier systems for highly insulated light weight walls: A laboratory investigation , 2012 .