Experimental and finite element analysis of EDM process and investigation of material removal rate by response surface methodology

In this study, thermal modeling and finite element simulation of electrical discharge machining (EDM) has been done, taking into account several important aspects such as temperature-dependent material properties, shape and size of the heated zone (Gaussian heat distribution), energy distribution factor, plasma flushing efficiency, and phase change to predict thermal behavior and material removal mechanism in EDM process. Temperature distribution on the cathode has been calculated using ANSYS finite element code, and the effect of EDM parameters on heat distribution along the radius and depth of the workpiece has been obtained. Temperature profiles have been used to calculate theoretical material removal rate (MRR) from the cathode. Theoretically calculated MRRs are compared with the experimental results, making it possible to precisely determine the portion of energy that enters the cathode for AISI H13 tool steel. Also in this paper, the effect of EDM parameters on MRR has been investigated by using the technique of design of experiments and response surface methodology. Finally, a quadratic polynomial regression model has been proposed for MRR, and the accuracy of this model has been checked by means of analysis of residuals.

[1]  Douglas C. Montgomery,et al.  Introduction to Statistical Quality Control , 1986 .

[2]  S. Oliaei,et al.  A numerical method for predicting depth of heat affected zone in EDM process for AISI H13 tool steel , 2011 .

[3]  A. Tekkaya,et al.  A semi-empirical approach for residual stresses in electric discharge machining (EDM) , 2006 .

[4]  I. Puertas,et al.  Analysis of the influence of EDM parameters on surface quality, MRR and EW of WC–Co , 2004 .

[5]  James V. Beck,et al.  Large time solutions for temperatures in a semi-infinite body with a disk heat source , 1981 .

[6]  S. S. Pande,et al.  Thermo-physical modeling of die-sinking EDM process , 2010 .

[7]  F. Klocke,et al.  EDM simulation: finite element-based calculation of deformation, microstructure and residual stresses , 2003 .

[8]  Xiaolin Chen,et al.  Process simulation of micro electro-discharge machining on molybdenum , 2007 .

[9]  H. Zarepour,et al.  Statistical analysis on electrode wear in EDM of tool steel DIN 1.2714 used in forging dies , 2007 .

[10]  Rajat Kumar Bhoi,et al.  Developing Transient Three Dimensional Thermal Models for Electro Discharge Machining of Semi Infinite and Infinite Solid , 2001 .

[11]  S. Yeo,et al.  Critical assessment and numerical comparison of electro-thermal models in EDM , 2008 .

[12]  Che Hassan Che Haron,et al.  Investigation on the influence of machining parameters when machining tool steel using EDM , 2001 .

[13]  P. C. Pandey,et al.  Analysis and modelling of edm parameters , 1982 .

[14]  Pradeep Kumar,et al.  Numerical simulation of powder mixed electric discharge machining (PMEDM) using finite element method , 2008, Math. Comput. Model..

[15]  Roger M. Sauter,et al.  Introduction to Statistical Quality Control (2nd ed.) , 1992 .

[16]  W. Dutré,et al.  Heat conduction model for the calculation of the volume of molten metal in electric discharges , 1974 .

[17]  James V. Beck,et al.  Transient temperatures in a semi-infinite cylinder heated by a disk heat source , 1981 .

[18]  V. K. Jain,et al.  ANALYSIS OF SPARK PROFILES DURING EDM PROCESS , 1997 .

[19]  Mohammadreza Shabgard,et al.  Mathematical and numerical modeling of the effect of input-parameters on the flushing efficiency of plasma channel in EDM process , 2013 .

[20]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model , 1989 .

[21]  Vijay K. Jain,et al.  Thermal stresses due to electrical discharge machining , 2002 .

[22]  P. C. Pandey,et al.  An analysis of surface erosion in electrical discharge machining , 1983 .

[23]  Deepak Kumar Panda.  Study of thermal stresses induced surface damage under growing plasma channel in electro-discharge machining , 2008 .

[24]  I. Puertas,et al.  Spacing roughness parameters study on the EDM of silicon carbide , 2005 .

[25]  A. Erden.  Effect of Materials on the Mechanism of Electric Discharge Machining (E.D.M.) , 1983 .