Characterization of the mechanical properties changes in an Al―Zn―Mg alloy after a two-step ageing treatment at 70° and 135 °C

Abstract Fine-scale precipitation of the η′ phase and its precursors are essential for the mechanical properties of Al-4.6 wt%Zn-1.2 wt%Mg alloy. This paper deals with an investigation of precipitation in an industrial Al–Zn–Mg alloy at various stages of a conventional two-step ageing treatment at 70 °C and 135 °C. The effect of microstructure on the mechanical properties was performed using microhardness and tensile tests, together with optical, scanning and transmission electron microscopy. After ageing at 135 °C, corresponding to the maximum value of hardness, small η′ precipitates were observed in the alloy matrix. After two-step ageing at 70 °C plus at 135 °C, the volume fraction of this precipitate becomes higher. Consequently, the yield strength of the material increases and it maintains its ductility. This high precipitate density slows the dislocation movement and thus a higher stress was required for its bowing.

[1]  C. Chen,et al.  Quantitative evaluation of precipitates in an Al–Zn–Mg–Cu alloy after isothermal aging , 2006 .

[2]  Elisabeth Aeby-Gautier,et al.  Precipitation sequences during quenching of the AA 7010 alloy , 2002 .

[3]  David Thevenet,et al.  Characteristics of the propagating deformation bands associated with the Portevin–Le Chatelier effect in an Al–Zn–Mg–Cu alloy , 2000 .

[4]  J. Dutkiewicz,et al.  STRUCTURE, TEXTURE AND MECHANICAL PROPERTIES OF ALZNMGCUZR ALLOY ROLLED AFTER HEAT TREATMENTS , 1997 .

[5]  X. Z. Li,et al.  GP-zones in Al–Zn–Mg alloys and their role in artificial aging , 2001 .

[6]  I. J. Polmear,et al.  T-phase Precipitation induced by the Addition of Silver to an Aluminium–Copper–Magnesium Alloy , 1966, Nature.

[7]  A. K. Mukhopadhyay.  Guinier-Preston zones in a high-purity Al-Zn-Mg alloy , 1994 .

[8]  C. Sigli,et al.  Structure and Property Control of Aerospace Alloys , 1997 .

[9]  E. Salamcı.  Ageing Behaviour of Spray Cast Al-Zn-Mg-Cu Alloys , 2001 .

[10]  Walter Rosenhain,et al.  Rosenhain Centenary conference . The contribution of physical metallurgy to engineering practice : a joint symposium held 22-24 September 1975 of the Metals Society, the National Physical Laboratory and the Royal Society , 1976 .

[11]  Y. Minggao,et al.  On the η′ precipitate phase in 7050 aluminium alloy , 1991 .

[12]  I. Torriani,et al.  Pre-precipitation study in the 7012 Al–Zn–Mg–Cu alloy by electrical resistivity , 2002 .

[13]  F. Plazaola,et al.  Study of formation and reversion of Guinier-Preston zones in Al-4.5 at%Zn-x at%Mg alloys by positrons , 1986 .

[14]  A. Ardell,et al.  Microstructures of the commercial 7075 Al alloy in the T651 and T7 tempers , 1983 .

[15]  J. Gjønnes,et al.  An electron microscope investigation of the microstructure in an aluminium-zinc-magnesium alloy , 1970 .

[16]  C. Mondal,et al.  On the nature of T(Al2Mg3Zn3) and S(Al2CuMg) phases present in as-cast and annealed 7055 aluminum alloy , 2005 .

[17]  A. Deschamps,et al.  Influence of predeformation on ageing in an Al–Zn–Mg alloy—I. Microstructure evolution and mechanical properties , 1998 .

[18]  A. Deschamps,et al.  Nature and distribution of quench-induced precipitation in an Al-Zn-Mg-Cu alloy , 1998 .

[19]  P. Cabot,et al.  Role of intermetallics in the activation of Al–Mg–Zn alloys , 1998 .

[20]  Wislei R. Osório,et al.  The interrelation between mechanical properties, corrosion resistance and microstructure of Pb–Sn casting alloys for lead-acid battery components , 2010 .

[21]  Alfred Cerezo,et al.  Early-stage precipitation in Al-Zn-Mg-Cu alloy (7050) , 2004 .

[22]  A. Deschamps,et al.  On the relationship between microstructure, strength and toughness in AA7050 aluminum alloy , 2003 .

[23]  M. Fine.  Phase transformations in condensed systems revisited: Industrial applications , 1996 .

[24]  R. Ferragut,et al.  On the two-step ageing of a commercial Al - Zn - Mg alloy; a study by positron lifetime spectroscopy , 1996 .

[25]  A. Deschamps,et al.  Characterisation of the composition and volume fraction of η′ and η precipitates in an Al–Zn–Mg alloy by a combination of atom probe, small-angle X-ray scattering and transmission electron microscopy , 2005 .

[26]  K. Stiller,et al.  Investigation of precipitation in an Al–Zn–Mg alloy after two-step ageing treatment at 100° and 150°C , 1999 .

[27]  Wojciech Szymański,et al.  Structural parameters of 7020 alloy after heat treatment simulating the welding process , 2001 .

[28]  J. C. Werenskiold,et al.  Characterization and modeling of precipitation kinetics in an Al-Zn-Mg alloy , 2000 .

[29]  F. Froes,et al.  Microstructure and properties of a new super-high-strength Al–Zn–Mg–Cu alloy C912 , 1997 .

[30]  Amauri Garcia,et al.  Design of mechanical properties of a Zn27Al alloy based on microstructure dendritic array spacing , 2007 .

[31]  J. Lendvai,et al.  Decomposition processes in Al-Zn-Mg alloys , 1983 .

[32]  R. Ferragut,et al.  Positron lifetime spectroscopy and decomposition processes in commercial Al-Zn-Mg-based alloys , 1998 .

[33]  Amauri Garcia,et al.  Effect of dendritic arm spacing on mechanical properties and corrosion resistance of Al 9 Wt Pct Si and Zn 27 Wt Pct Al alloys , 2006 .