Analysis of Mode-Split Operation in MEMS Based on Piezoresistive Nanogauges

Microelectromechanical system (MEMS) sensors based on nanoscale piezoresistive sensing elements (nanogauges) can have mechanical modes either related only to micrometric springs or related also to nanogauge constraints. Due to the different impact that fabrication process imperfections have on these two kinds of modes, their correlation can be poorer from part to part than in sensors based on capacitive readout. In this context, this paper compares the correlation between two modes in MEMS with and without nanogauges. Experiments show a ± 30% relative variation in the modes difference over 26 samples of the former type, which is more than 3.5 times more than what observed on similar structures with no nanogauges. A theoretical model identifies the sources of this fluctuation (local etching and height nonuniformities), and predicts the behavior and improvements using different springs design.

[1]  G. Jourdan,et al.  M&NEMS: A new approach for ultra-low cost 3D inertial sensor , 2009, 2009 IEEE Sensors.

[2]  A.A. Trusov,et al.  Environmentally Robust MEMS Vibratory Gyroscopes for Automotive Applications , 2009, IEEE Sensors Journal.

[3]  T. Akin,et al.  A single-crystal silicon symmetrical and decoupled MEMS gyroscope on an insulating substrate , 2005, Journal of Microelectromechanical Systems.

[4]  Farrokh Ayazi,et al.  A Sub-0.2$^{\circ}/$ hr Bias Drift Micromechanical Silicon Gyroscope With Automatic CMOS Mode-Matching , 2009, IEEE Journal of Solid-State Circuits.

[5]  Farrokh Ayazi,et al.  Micromachined inertial sensors , 1998, Proc. IEEE.

[6]  Guillaume Jourdan,et al.  3D Magnetic Field Sensor Concept for Use in Inertial Measurement Units (IMUs) , 2014, Journal of Microelectromechanical Systems.

[7]  F. Souchon,et al.  3-Axis gyroscope with Si nanogage piezo-resistive detection , 2012, 2012 IEEE 25th International Conference on Micro Electro Mechanical Systems (MEMS).

[8]  Giacomo Langfelder,et al.  A Versatile Instrument for the Characterization of Capacitive Micro- and Nanoelectromechanical Systems , 2012, IEEE Transactions on Instrumentation and Measurement.

[9]  A.A. Trusov,et al.  Gyroscope architecture with structurally forced anti-phase drive-mode and linearly coupled anti-phase sense-mode , 2009, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[10]  Volker Kempe.  Inertial MEMS: Gyroscopes , 2011 .

[11]  B.E. Boser,et al.  A Mode-Matching $\Sigma\Delta$ Closed-Loop Vibratory Gyroscope Readout Interface With a 0.004$^{\circ}$ /s/$\surd{\hbox{Hz}}$ Noise Floor Over a 50 Hz Band , 2008, IEEE Journal of Solid-State Circuits.

[12]  Qian Cheng Zhao,et al.  A Lateral-Axis Microelectromechanical Tuning-Fork Gyroscope With Decoupled Comb Drive Operating at Atmospheric Pressure , 2010, Journal of Microelectromechanical Systems.

[13]  R. Neul,et al.  Micromachined Angular Rate Sensors for Automotive Applications , 2007, IEEE Sensors Journal.

[14]  Giacomo Langfelder,et al.  Operation of Lorentz-Force MEMS Magnetometers With a Frequency Offset Between Driving Current and Mechanical Resonance , 2014, IEEE Transactions on Magnetics.

[15]  G Langfelder,et al.  MEMS Motion Sensors Based on the Variations of the Fringe Capacitances , 2011, IEEE Sensors Journal.

[16]  Giacomo Langfelder,et al.  The Dependence of Fatigue in Microelectromechanical Systems on the Environment and the Industrial Packaging , 2012, IEEE Transactions on Industrial Electronics.

[18]  Bernhard E. Boser,et al.  3 A Mode-Matching ΔΣ Closed-Loop Vibratory-Gyroscope Readout Interface with a 0 . 004 ° / s / √ Hz Noise Floor over a 50 Hz Band , 2008 .

[19]  Giacomo Langfelder,et al.  Off-Resonance Low-Pressure Operation of Lorentz Force MEMS Magnetometers , 2014, IEEE Transactions on Industrial Electronics.

[20]  R. Anciant,et al.  Bias Contributions in a MEMS Tuning Fork Gyroscope , 2013, Journal of Microelectromechanical Systems.