Micromachining features of TiC ceramic by femtosecond pulsed laser

Femtosecond pulsed laser was employed to drill blind holes (or circle surfaces) and through holes in titanium carbide (TiC) ceramic by the helical drilling technique. The effects of spiral number, processing time, laser fluence and repetition rate on the qualities of holes (or circle surfaces) were investigated. Morphology of holes (or circle surfaces) and composition of irradiated areas were analyzed by a scanning electron microscope (SEM), a three-dimensional super depth digital microscope and energy dispersive spectroscopy (EDS), etc. The results indicated that laser fluence and repetition rate had major effects on ablation efficiency and quality. Blind holes with taper bottom were observed when the laser fluence was above 6.37 x 10(-1) J/mm(2). With the increase of laser fluence, hole depth increased firstly and then decreased. The change in hole diameter decreased when the laser fluence was above 0.51 J/mm(2). The effects of repetition rate on hole depth were similar to that of laser fluence, while it showed a faint change in hole diameter at laser fluence of 1.02 J/mm(2) and laser repetition rate ranging from 2 to 140 kHz. Furthermore, through holes were attained at narrowed laser fluence ranging from 0.51 to 1.53 J/mm(2). The drilled holes had good circular geometry for entrance and exit. (C) 2015 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

[1]  R. Freer.  The Physics and Chemistry of Carbides, Nitrides and Borides , 1990 .

[2]  Walter Perrie,et al.  Femtosecond laser micro-structuring of alumina ceramic , 2005 .

[3]  Hyun Wook Kang,et al.  Enhancement of bovine bone ablation assisted by a transparent liquid Layer on a target surface , 2006, IEEE Journal of Quantum Electronics.

[4]  Deng Jianxin,et al.  Surface integrity in electro-discharge machining, ultrasonic machining, and diamond saw cutting of ceramic composites , 2000 .

[5]  Guanwei Liu,et al.  Spark plasma sintering of TiC ceramic with tungsten carbide as a sintering additive , 2013 .

[6]  Jagdev Singh,et al.  Fuzzy Modeling and Simulation of Ultrasonic Drilling of Porcelain Ceramic with Hollow Stainless Steel Tools , 2009 .

[7]  J. L. Tan,et al.  Femtosecond laser drilling of alumina ceramic substrates , 2010 .

[8]  Seung Ki Moon,et al.  Influence of substrate heating on hole geometry and spatter area in femtosecond laser drilling of silicon , 2014 .

[9]  Generation of debris in the femtosecond laser machining of a silicon substrate , 2005 .

[10]  Litong Zhang,et al.  Ultra-short pulse laser deep drilling of C/SiC composites in air , 2013 .

[11]  N. Dahotre,et al.  Laser machining of structural ceramics—A review , 2009 .

[12]  Hong Wang,et al.  Femtosecond laser directly writing microholes in Bi(Nb0.998V0.002)O4 ceramic and multi-photon induced large scale nanometer wires array , 2011 .

[13]  João Cirilo da Silva Neto,et al.  Intervening variables in electrochemical machining , 2006 .

[14]  L. Zhao,et al.  Electrical discharge machining of ceramic matrix composites with ceramic fiber reinforcements , 2013 .

[15]  Ruediger Grunwald,et al.  Femtosecond laser-induced periodic surface structures revisited: A comparative study on ZnO , 2009 .

[16]  Stefan Nolte,et al.  Laser helical drilling of silicon wafers with ns to fs pulses: Scanning electron microscopy and transmission electron microscopy characterization of drilled through-holes , 2006 .

[17]  Raju Pawade,et al.  Effect of process parameters on MRR, TWR and surface topography in ultrasonic machining of alumina–zirconia ceramic composite , 2014 .

[18]  Hyunho Shin,et al.  A method to quantify the drilling machinability of machinable ceramics from the viewpoint of preventing chipping , 2013 .

[19]  R. Karthikeyan,et al.  Study of electrochemical machining characteristics of Al/SiCp composites , 2009 .

[20]  A. Rosenfeld,et al.  On the role of surface plasmon polaritons in the formation of laser-induced periodic surface structures upon irradiation of silicon by femtosecond-laser pulses , 2009 .

[21]  S. Nikumb,et al.  Femtosecond Laser Drilling of Alumina Wafers , 2009 .

[22]  C. Tang,et al.  Surface integrity and modification of electro-discharge machined alumina-based ceramic composite , 2002 .

[23]  Qingliang Zhao,et al.  Ablation Threshold and Material Removal Mechanisms of SiC Processed by Femtosecond Laser , 2010 .

[24]  G. D. Shandybina,et al.  Ultrashort excitations of surface polaritons and waveguide modes in semiconductors , 2008 .

[25]  Jian Liu,et al.  Micro-hole drilling and cutting using femtosecond fiber laser , 2014 .

[26]  Feng Qin,et al.  Size Effects in Cutting With a Diamond-Coated Tool , 2011 .

[27]  Yong Huang,et al.  New laser machining technology of Al2O3 ceramic with complex shape , 2012 .

[28]  S. Bai,et al.  A low cost fabrication route for continuous carbon fiber reinforced TiC based ceramic matrix composite , 2012 .

[29]  Y. Lam,et al.  Influence of substrate cooling on femtosecond laser machined hole depth and diameter , 2007 .

[30]  J. Ihlemann,et al.  Femtosecond ultraviolet laser micromachining of Al2O3–TiC ceramics , 1999 .

[31]  V. Semak,et al.  Peculiarity of metal drilling with a commercial femtosecond laser , 2007 .

[32]  Jianxin Deng,et al.  Multiple nanoscale parallel grooves formed on Si3N4/TiC ceramic by femtosecond pulsed laser , 2014 .

[33]  M. Polański,et al.  A simple method of synthesis and surface purification of titanium carbide powder , 2013 .

[34]  Petar Piljek,et al.  Micromachining - review of literature from 1980 to 2010 , 2014 .