3D modeling of an HT-PEFC stack using reformate gas

Abstract A computational fluid dynamics model is presented, which is suitable to perform full stack simulations of a high temperature polymer electrolyte fuel cell with reasonable computational power and time. The model is based on a previously presented multi-domain and multi-scale model and is extended by electrochemical equations suitable for operation with reformate gas. Model results show very good agreement with the local current density and temperature distributions which were obtained by stack experiments. A general analysis of possible flow configurations regarding anode, cathode and cooling fluid inside a stack is performed. The most favorite configuration with regard to current density homogenization is anode and cathode in counter-flow with cooling and anode in co-flow. This result is confirmed by stack experiments.

[1]  Frano Barbir,et al.  PEM Fuel Cells , 2006 .

[2]  D. Stolten,et al.  Performance Analysis of HT-PEFC Stacks , 2012 .

[3]  Xianguo Li,et al.  Three-dimensional non-isothermal modeling of carbon monoxide poisoning in high temperature proton exchange membrane fuel cells with phosphoric acid doped polybenzimidazole membranes , 2011 .

[4]  A. Bendzulla.  Von der Komponente zum Stack: Entwicklung und Auslegung von HT-PEFC-Stacks der 5 kW-Klasse , 2010 .

[5]  H. Dhar,et al.  Nature of CO Adsorption during H 2 Oxidation in Relation to Modeling for CO Poisoning of a Fuel Cell Anode , 1987 .

[6]  A. A. Kulikovsky,et al.  The effect of stoichiometric ratio λ on the performance of a polymer electrolyte fuel cell , 2004 .

[7]  E. Davydova,et al.  CO tolerance and CO oxidation at Pt and Pt-Ru anode catalysts in fuel cell with polybenzimidazole-H3PO4 membrane , 2010 .

[8]  Werner Lehnert,et al.  3D modeling of a 200 cm2 HT-PEFC short stack , 2012 .

[9]  Alexander V. Chertovich,et al.  A simple model of a high temperature PEM fuel cell , 2010 .

[10]  R. O’Hayre,et al.  Fuel Cell Fundamentals , 2005 .

[11]  Matthew M. Mench,et al.  Fuel Cell Engines , 2008 .

[12]  Hyung Jin Sung,et al.  Effect of GDL permeability on water and thermal management in PEMFCs - I. Isotropic and anisotropic permeability , 2008 .

[13]  Søren Knudsen Kær,et al.  Part one: A novel model of HTPEM-based micro-combined heat and power fuel cell system , 2008 .

[14]  A. Reis,et al.  Experimental evaluation of CO poisoning on the performance of a high temperature proton exchange membrane fuel cell , 2009 .

[15]  Andrei A. Kulikovsky,et al.  Analytical Modelling of Fuel Cells , 2010 .

[16]  T. Springer,et al.  Model for polymer electrolyte fuel cell operation on reformate feed , 2001 .

[17]  P. Stonehart,et al.  Reaction pathways and poisons—II: The rate controlling step for electrochemical oxidation of hydrogen on Pt in acid and poisoning of the reaction by CO , 1975 .

[18]  S. Chan,et al.  Computational fluid dynamics simulation of polymer electrolyte membrane fuel cells operating on reformate , 2011 .

[19]  K. Scott,et al.  A High Temperature Polymer Electrolyte Membrane Fuel Cell Model for Reformate Gas , 2011 .

[20]  Søren Knudsen Kær,et al.  Experimental characterization and modeling of commercial polybenzimidazole-based MEA performance , 2006 .

[21]  Jon G. Pharoah,et al.  A comparison of different approaches to modelling the PEMFC catalyst layer , 2008 .

[22]  T. Kurz,et al.  Modelling of CO Poisoning and its Dynamics in HTPEM Fuel Cells , 2010 .

[23]  S. Kjelstrup,et al.  Three steps in the anode reaction of the polymer electrolyte membrane fuel cell. Effect of CO , 2007 .