Cold start characteristics of proton exchange membrane fuel cells

Abstract In this study, the effects of the start-up temperature, load condition and flow arrangement on the cold start characteristics and performance of a proton exchange membrane fuel cell (PEMFC) are investigated through in-situ experiments with the simultaneous measurements of the current and temperature distributions. Rather than the commonly recognized cold start failure mode due to the ice blockage in cathode catalyst layer (CL), another failure mode due to the ice blockage in flow channel and gas diffusion layer (GDL) leading to significantly high pressure drop through cathode flow field is observed at a start-up temperature just below the lowest successful start-up temperature. Three ice formation mechanisms are proposed, corresponding to the ice formations in cathode CL, GDL and flow channel. The general distributions of current densities and temperatures during the constant current cold start processes are similar to the constant voltage cold start processes, except that the temperatures at the end of the constant current cold start processes are more evenly distributed over the active reaction area because of the increased heat generation rates. The cold start characteristics are mainly dominated by the cathode flow, and changing the flow arrangement has unimportant impact on the cold start performance.

[1]  Sébastien Rosini,et al.  Experimental and theoretical investigations on a proton exchange membrane fuel cell starting up at subzero temperatures , 2009 .

[2]  Xianguo Li,et al.  Three-dimensional multiphase modeling of cold start processes in polymer electrolyte membrane fuel cells , 2009 .

[3]  Xianguo Li,et al.  Effects of various operating and initial conditions on cold start performance of polymer electrolyte membrane fuel cells , 2009 .

[4]  Chao-Yang Wang,et al.  Isothermal Cold Start of Polymer Electrolyte Fuel Cells , 2007 .

[5]  Qunhui Guo,et al.  Effect of freeze-thaw cycles on the properties and performance of membrane-electrode assemblies , 2006 .

[6]  Rodney L. Borup,et al.  Cold start of polymer electrolyte fuel cells: Three-stage startup characterization , 2010 .

[7]  Hossein Toghiani,et al.  Effect of sub-freezing temperatures on a PEM fuel cell performance, startup and fuel cell components , 2006 .

[8]  Kazuhiko Yoshida,et al.  Behavior of water below the freezing point in PEFCs , 2007 .

[9]  S. Specchia,et al.  Experimental studies on Nafion 112 single PEM-FCs exposed to freezing conditions , 2011 .

[10]  Jianlu Zhang,et al.  Effects of Hardware Design and Operation Conditions on PEM Fuel Cell Water Flooding , 2010 .

[11]  Young-Jun Sohn,et al.  Investigation of freeze/thaw durability in polymer electrolyte fuel cells , 2010 .

[12]  Masahiro Shiozawa,et al.  Super-cooled water behavior inside polymer electrolyte fuel cell cross-section below freezing temperature , 2008 .

[13]  Manish Khandelwal,et al.  One-dimensional thermal model of cold-start in a polymer electrolyte fuel cell stack , 2007 .

[14]  Chao-Yang Wang,et al.  Non-isothermal cold start of polymer electrolyte fuel cells , 2007 .

[15]  Chao-Yang Wang,et al.  Effects of operating and design parameters on PEFC cold start , 2007 .

[16]  Xianguo Li,et al.  Simultaneous measurement of current and temperature distributions in a proton exchange membrane fuel cell during cold start processes , 2011 .

[17]  J. Jorné,et al.  Investigation of Low-Temperature Proton Transport in Nafion Using Direct Current Conductivity and Differential Scanning Calorimetry , 2006 .

[18]  Chaoyang Wang,et al.  Effect of Cathode Pore Volume on PEM Fuel Cell Cold Start , 2010 .

[19]  Shanhai Ge,et al.  Characteristics of subzero startup and water/ice formation on the catalyst layer in a polymer electrolyte fuel cell , 2007 .

[20]  Shanhai Ge,et al.  In Situ Imaging of Liquid Water and Ice Formation in an Operating PEFC during Cold Start , 2006 .

[21]  Xianguo Li,et al.  Cold start analysis of polymer electrolyte membrane fuel cells , 2010 .

[22]  Xianguo Li,et al.  Water transport in polymer electrolyte membrane fuel cells , 2011 .

[23]  Hua Meng,et al.  Numerical analyses of non-isothermal self-start behaviors of PEM fuel cells from subfreezing startup temperatures , 2008 .

[24]  Hua Meng,et al.  A PEM fuel cell model for cold-start simulations , 2008 .

[25]  Dirk Riemann,et al.  Low temperature operation and influence parameters on the cold start ability of portable PEMFCs , 2006 .

[26]  Zhigang Shao,et al.  Investigation of resided water effects on PEM fuel cell after cold start , 2007 .

[27]  Wei Liu,et al.  Degradation behaviors of polymer electrolyte membrane fuel cell under freeze/thaw cycles , 2010 .

[28]  Zhigang Shao,et al.  Characteristics of proton exchange membrane fuel cells cold start with silica in cathode catalyst layers , 2010 .

[29]  S. Guo,et al.  Single-Channel Analysis of Proton Exchange Membrane Fuel Cell , 2010 .

[30]  Xianguo Li,et al.  Effects of a microporous layer on the performance degradation of proton exchange membrane fuel cells through repetitive freezing , 2011 .

[31]  Yun Wang,et al.  Analysis of the Key Parameters in the Cold Start of Polymer Electrolyte Fuel Cells , 2007 .

[32]  Sarit K. Das,et al.  The Performance Analysis of a Multi-Duct Proton Exchange Membrane Fuel Cell Cathode , 2008 .