Interfacial reaction and mechanical reliability of PTH solder joints with different solder/surface finish combinations

Abstract The effects of minor Ni addition (0.05 wt.%) on the microstructures and mechanical reliability of the lead-free solder joints used in the pin through hole (PTH) components were carefully investigated using a scanning electron microscope (SEM), a field-emission electron probe x-ray microanalyzer, and a pull tester. The PTH walls (i.e., Cu) of printed circuit boards (PCBs) were coated with organic solderability preservative (OSP) or electroless nickel/immersion gold (ENIG) surface finish before soldering. During soldering, the pins of the electronic components were first inserted into the PTHs deposited with OSP or ENIG, and then joined using a Sn–3Ag–0.5Cu (SAC) solder bath through a typical wave-soldering process. After wave soldering, a rework (the second wave soldering) was performed, where an SAC or Sn–0.7Cu–0.05Ni (SCN) solder bath was employed. The SCN joints were found to possess a higher tensile strength than the SAC ones in the OSP case. The sluggish growth of Cu 3 Sn, along with few Kirkendall voids at the solder/Cu interface caused by minor Ni addition into the solder alloy (i.e., SCN), was believed to be the root cause responsible for the increase in the strength value. However, the mechanical strength of the PTH components was revealed to be insensitive to the solder composition in the alternative case where an ENIG was deposited over the PTH walls. The implication of this study revealed that minor addition of Ni into the solder is beneficial for the solder/Cu joints, but for the solder/Ni(P) joints.

[1]  Jin Yu,et al.  Effects of residual S on Kirkendall void formation at Cu/Sn–3.5Ag solder joints , 2008 .

[2]  J. Kivilahti,et al.  Effect of Ni on the formation of Cu/sub 6/Sn/sub 5/ and Cu/sub 3/Sn intermetallics , 2006, 56th Electronic Components and Technology Conference 2006.

[3]  Tomi Laurila,et al.  Impurity and alloying effects on interfacial reaction layers in Pb-free soldering , 2010 .

[4]  Wojciech Gierlotka,et al.  Development and Evaluation of Direct Deposition of Au/Pd(P) Bilayers over Cu Pads in Soldering Applications , 2012, Journal of Electronic Materials.

[5]  C. Kao,et al.  Effects of minor Fe, Co, and Ni additions on the reaction between SnAgCu solder and Cu , 2009 .

[6]  W. Wu,et al.  Comparative study between Sn37Pb and Sn3Ag0.5Cu soldering with Au/Pd/Ni(P) tri-layer structure , 2010 .

[7]  K. Bae,et al.  Interdiffusion analysis of the soldering reactions in Sn-3.5Ag/Cu couples , 2001 .

[8]  K. S. Kim,et al.  Effects of fourth alloying additive on microstructures and tensile properties of Sn-Ag-Cu alloy and joints with Cu , 2003, Microelectron. Reliab..

[9]  Iver E. Anderson,et al.  Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints , 2006 .

[10]  Kazuaki Ano,et al.  Kirkendall void formation in eutectic SnPb solder joints on bare Cu and its effect on joint reliability , 2005 .

[11]  Kwang-Lung Lin,et al.  Effect of microelements addition on the interfacial reaction between Sn-Ag-Cu solders and the Cu substrate , 2003 .

[12]  Yee-Wen Yen,et al.  Interfacial reactions in Ag-Sn/Cu couples , 1999 .

[13]  C. Kao,et al.  Interfacial reaction issues for lead-free electronic solders , 2006 .

[14]  A. S. Zuruzi,et al.  Kinetics of copper and high Pb/high Sn bilayered Pb-Sn solder interactions , 1999 .

[15]  J. Duh,et al.  Direct evidence for a Cu-enriched region at the boundary between Cu6Sn5 and Cu3Sn during Cu/Sn reaction , 2010 .

[16]  C. S. Lin,et al.  Influence of Palladium Thickness on the Soldering Reactions Between Sn-3Ag-0.5Cu and Au/Pd(P)/Ni(P) Surface Finish , 2010 .

[17]  C. C. Wang,et al.  Field-emission transmission electron microscopy study of the reaction sequence between Sn–Ag–Cu alloy and an amorphous Pd(P) thin film in microelectronic packaging , 2013 .

[18]  Cheng-En Ho,et al.  Inhibiting the growth of Cu3Sn and Kirkendall voids in the Cu/Sn-Ag-Cu system by minor Pd alloying , 2012, Electronic Materials Letters.

[19]  Z. Bagheri,et al.  Microstructure and Reliability Comparison of Different Pb-Free Alloys Used for Wave Soldering and Rework , 2009 .

[20]  King-Ning Tu,et al.  Kinetics of interfacial reaction in bimetallic CuSn thin films , 1982 .

[21]  F. Guo.  Composite lead-free electronic solders , 2006 .

[22]  Chih Chen,et al.  Transition from flip chip solder joint to 3D IC microbump: Its effect on microstructure anisotropy , 2013, Microelectron. Reliab..

[23]  C. Robert Kao,et al.  Effects of Joining Sequence on the Interfacial Reactions and Substrate Dissolution Behaviors in Ni/Solder/Cu Joints , 2011 .

[24]  K. Nogita,et al.  Cracking and phase stability in reaction layers between Sn-Cu-Ni solders and Cu substrates , 2009 .

[25]  Chih-Ming Chen,et al.  Solid-state interfacial reactions at the solder joints employing Au/Pd/Ni and Au/Ni as the surface finish metallizations , 2012, Microelectron. Reliab..

[26]  William J. Boettinger,et al.  Diffusion Parameters and Growth Mechanism of Phases in the Cu-Sn System , 2011 .

[27]  W. Wu,et al.  Reliability evaluation on a submicron Ni(P) thin film for lead-free soldering , 2013 .

[28]  G. Ghosh.  Kinetics of interfacial reaction between eutectic Sn-Pb solder and Cu/Ni/Pd metallizations , 1999 .

[29]  K. Tu,et al.  Time- and temperature-dependent wetting behavior of eutectic SnPb on Cu leadframes plated with Pd/Ni and Au/Pd/Ni thin films , 1998 .