Characterization of Expanded Polypropylene Bead Foams with Modified Steam-Chest Molding

Steam is commonly used in polymer bead foam sintering due to its high heat transfer capacity. However, the pressure loss unavoidable during flow through the beads causes a temperature decrease and thereby negatively affects the sintering behavior. In order to reduce the sensitivity of the temperature to the pressure variation, hot air was added to the steam line. The effects of the flow rate, the pressure, and the temperature of the hot air on the surface roughness, thermal properties, and mechanical properties of the molded products were studied. The results showed that the introduction of hot air at a flow rate of 120 L/min decreased the total steaming time by about 32%. Further, a decrease of 16 °C in the processing temperature was observed, which decreased the surface roughness by 50%. Hot air improved the heat flow and thereby enhanced the uniformity of the tensile properties across the molded part.

[1]  Chul B. Park,et al.  Double Crystal Melting Peak Generation for Expanded Polypropylene Bead Foam Manufacturing , 2013 .

[2]  Chul B. Park,et al.  Critical processing parameters for foamed bead manufacturing in a lab-scale autoclave system , 2013 .

[3]  Chul B. Park,et al.  Steam-Chest Molding of Expanded Polypropylene Foams. 2. Mechanism of Interbead Bonding , 2011 .

[4]  Chul B. Park,et al.  Steam-Chest Molding of Expanded Polypropylene Foams. 1. DSC Simulation of Bead Foam Processing , 2010 .

[5]  Philippe Viot,et al.  Hydrostatic compression on polypropylene foam , 2009 .

[6]  Philippe Viot,et al.  Polypropylene foam behaviour under dynamic loadings : Strain rate, density and microstructure effects , 2009 .

[7]  M. Ohshima,et al.  Numerical simulation of a polypropylene foam bead expansion process , 2008 .

[8]  Jin‐San Yoon,et al.  Formation of Double Melting Peak of Poly(propylene-co-ethylene-co-1-butene) during the Preexpansion Process for Production of Expanded Polypropylene , 2005 .

[9]  M. Champagne,et al.  Impact-Compression-Morphology Relationship in Polyolefin Foams , 2005 .

[10]  J. Schut.  Expandable bead molding goes high-tech , 2005 .

[11]  I. Beverte.  Deformation of Polypropylene Foam Neopolen® P in Compression , 2004 .

[12]  S. Shivkumar,et al.  Bead fusion in polystyrene foams , 2003 .

[13]  G. Belingardi,et al.  Characterization of polymeric structural foams under compressive impact loading by means of energy-absorption diagram , 2001 .

[14]  N. J. Mills,et al.  The Effect of Water Immersion on the Mechanical Properties of Polystyrene Bead Foam Used in Soft Shell Cycle Helmets , 1994 .

[15]  P. R. Stupak,et al.  The Effect of Bead Fusion on the Energy Absorption of Polystyrene Foam. Part I: Fracture Toughness , 1991 .

[16]  P. R. Stupak,et al.  The Effect of Bead Fusion on the Energy Absorption of Polystyrene Foam. Part II: Energy Absorption , 1991 .

[17]  Akira Nagashima,et al.  Viscosity and thermal conductivity of dry air in the gaseous phase , 1985 .

[18]  F. G. Keyes,et al.  The thermal conductivity of steam , 1964 .

[19]  J. R. Roebuck.  The Joule-Thomson Effect in Air. , 1926, Proceedings of the National Academy of Sciences of the United States of America.