LOCAL WALL SHEAR STRESS VARIATIONS PREDICTED BY COMPUTATIONAL FLUID DYNAMICS FOR HYGIENIC DESIGN

Food producers depend to a great extent on the availability of easy-to-clean processing equipment. This paper presents initial work carried out to improve the application of commercially available computational fluid dynamics (CFD) programs as a tool to improve hygienic design of food processing equipment. In the present paper, previous work on using CFD to improve hygienic design are combined with work that shows the importance of measured local mean wall shear stresses and the fluctuations in these wall shear stresses with respect to cleaning effects of the flow. Results of wall shear stress and the fluctuations acquired by the measuring technique are difficult to apply directly for actual design optimization. Instead, steady-state CFD simulations using STAR-CD were applied to predict the fluctuation of equivalent mean wall shear stresses on the entire surface of pipes with various diameter changes (gradual and sudden expansions or contractions). Measured fluctuation rates of wall shear stress are shown to be analogous to the turbulence intensity in the near-wall region predicted by CFD simulations. The results are promising; hence, an important step has been taken towards setting up a method for evaluating cleanability by steady-state CFD simulations based on evaluation of the mean wall shear stresses and the turbulence intensity.

[1]  D. Seguin,et al.  Experimental characterisation of flow regimes in various porous media—I: Limit of laminar flow regime , 1998 .

[2]  V. C. Patel,et al.  Near-wall turbulence models for complex flows including separation , 1988 .

[3]  J. Visser.  Measurement of the force of adhesion between submicron carbon-black particles and a cellulose film in aqueous solution , 1970 .

[4]  Albrecht Graßhoff,et al.  Hygienic design—the basis for computer controlled automation , 1992 .

[5]  H. L. Norris,et al.  Turbulent channel flow with a moving wavy boundary , 1975 .

[6]  B. Desmet,et al.  Numerical study of the wall shear stress produced by the impingement of a plane turbulent jet on a plate , 1997 .

[7]  Alan Friis,et al.  Hygienic Design of Closed Processing Equipment by use of Computational Fluid Dynamics , 2003 .

[8]  F. Hauser,et al.  Deformation and Fracture Mechanics of Engineering Materials , 1976 .

[9]  B. Yates,et al.  Mechanism of detachment of colloidal particles from a flat substrate in a turbulent flow , 1973 .

[10]  Jack Legrand,et al.  Use of electrochemical sensors for the determination of wall turbulence characteristics in annular swirling decaying flows , 1997 .

[11]  Alan Friis,et al.  Critical wall shear stress for the EHEDG test method , 2004 .

[12]  S. Craig,et al.  Heat transfer to pseudoplastic fluids in laminar flow , 1962 .

[13]  M. A. Latifi,et al.  Hydrodynamics of liquid flow in packed beds: an experimental study using electrochemical shear rate sensors , 1994 .

[14]  H. L. M. Lelieveld,et al.  Hygiene in food processing , 2003 .

[15]  R. A. Stevens,et al.  The effect of wiping and spray-wash temperature on bacterial retention on abraded domestic sink surfaces , 1993 .

[16]  Wolfgang Rodi,et al.  Experience with two-layer models combining the k-epsilon model with a one-equation model near the wall , 1991 .

[17]  Thomas J. Hanratty,et al.  An experimental study of the unsteady nature of the viscous sublayer , 1963 .

[18]  J. Austin,et al.  Development of bacterial biofilms in dairy processing lines , 1995, Journal of Dairy Research.

[19]  H. Schlichting.  Boundary Layer Theory , 1955 .

[20]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[21]  Mukul M. Sharma,et al.  Factors controlling the hydrodynamic detachment of particles from surfaces , 1992 .

[22]  Jack Legrand,et al.  Cleaning in place: effect of local wall shear stress variation on bacterial removal from stainless steel equipment , 2002 .