Study on UV laser machining quality of carbon fibre reinforced composites

The large differences in material properties of the carbon fibre and the epoxy resin in carbon fibre reinforced plastic (CFRP) composite make laser processing very challenging. The heat affected zone (HAZ) has been the major obstacle for wide industry applications of laser machining of CFRP composites. This paper investigates the quality of CFRP machined by a diode pumped solid state (DPSS) UV laser. The results show that minimum HAZ (about 50 μm) is achievable in machining of CFRP composite by using short pulsed UV laser. The study found that heat is easily accumulated in the material during laser processing, especially when the carbon fibres are sliced into small pieces. The paper discusses how to make use of the heat accumulation and how to avoid potential damage by the heat accumulation. Bearing strengths test and fracturing mechanisms study were conducted. Method of characterization of thermal damage in polymer matrix is developed.

[1]  Stefan Hallström,et al.  Bearing strength of carbon fibre/epoxy laminates: effects of bolt-hole clearance , 2004 .

[2]  Giuseppe Daurelio,et al.  Laser cutting of different polymeric plastics (PE, PP and PC) by a CO2 laser beam , 2005 .

[3]  Tagliaferri,et al.  Cut edge quality of GFRP by pulsed laser: laser-material interaction analysis , 1987 .

[4]  T. M. Yue,et al.  A study of the heat-affected zone in the UV YAG laser drilling of GFRP materials , 2002 .

[5]  A. Abrão,et al.  Drilling of fiber reinforced plastics: A review , 2007 .

[6]  A. Jawaid,et al.  Machining of advanced engineering materials using traditional and laser techniques , 1994 .

[7]  J. Mathew,et al.  Parametric studies on pulsed Nd:YAG laser cutting of carbon fibre reinforced plastic composites , 1999 .

[8]  A. Cenna,et al.  Evaluation of cut quality of fibre-reinforced plastics : A review , 1997 .

[9]  Paul Mativenga,et al.  Laser machining of carbon fibre-reinforced plastic composites , 2010 .

[10]  Dieter Bäuerle,et al.  Laser processing and chemistry: recent developments , 2002 .

[11]  Brian Rooks,et al.  Laser processing of plastics , 2004, Ind. Robot.

[12]  M. Brandt,et al.  Comparative study of jetting machining technologies over laser machining technology for cutting composite materials , 2002 .

[13]  Trevor M. Young,et al.  Durability of hybrid laminar flow control (HLFC) surfaces , 2003 .

[14]  Toshiki Hirogaki,et al.  Study on small diameter drilling in GFRP , 1995 .

[15]  J. Paulo Davim,et al.  Some experimental studies on CO2 laser cutting quality of polymeric materials , 2008 .

[16]  A. Di Ilio,et al.  Laser cutting of fibre-reinforced polyesters , 1985 .

[17]  S. Mahdavian,et al.  Experimental and theoretical analyses of cutting nonmetallic materials by low power CO2-laser , 2004 .

[18]  Paul Mativenga,et al.  Numerical simulation of laser machining of carbon-fibre-reinforced composites , 2010 .

[19]  J. Paulo Davim,et al.  Evaluation of cutting quality of PMMA using CO2 lasers , 2008 .

[20]  C. I. Chang,et al.  Thermal Response of Graphite Epoxy Composite Subjected to Rapid Heating , 1981 .

[21]  Eckart Uhlmann,et al.  The extent of laser-induced thermal damage of UD and crossply composite laminates , 1999 .

[22]  F. C. Campbell.  Manufacturing Processes for Advanced Composites , 2012 .

[23]  V. Tagliaferri,et al.  Maximum cutting speed in laser cutting of fiber reinforced plastics , 1988 .