Machining fixture layout optimization using FEM and evolutionary techniques

Design of fixture configuration (layout) is a procedure to establish the workpiece fixture contact through positioning of clamps and locating elements such that the workpiece elastic deformation is minimized. This work is done based on the assumption that the workpiece is an elastic body. Since the fixture layout influences the dimensional and form accuracy of the workpiece during the machining process, the fixture layout has to be optimized to minimize the workpiece deformation. In this paper, the workpiece deformation is modeled using finite element method (FEM), for the problem of fixture layout optimization problems with the objective of minimizing the dimensional and form errors. This paper presents a fixture layout optimization method that uses genetic algorithm (GA) and ant colony algorithm (ACA) separately. In this paper, three different number of node systems are defined on the same workpiece geometry to find the consistency in the performance of GA and ACA. The optimal solution, i.e., the most minimum value among the entire possible layout is determined separately for all three different number of node systems. The solution obtained for each node system using GA and ACA is compared with their respective optimal solution separately and ACA reports faster and accurate solutions.

[1]  Kamal Youcef-Toumi,et al.  Kinematic methods for automated fixture reconfiguration planning , 1990, Proceedings., IEEE International Conference on Robotics and Automation.

[2]  H. Harry Asada,et al.  Kinematic analysis of workpart fixturing for flexible assembly with automatically reconfigurable fixtures , 1985, IEEE J. Robotics Autom..

[3]  Yiming Rong,et al.  Automated Generation of Fixture Configuration Design , 1997 .

[4]  Shreyes N. Melkote,et al.  Machining fixture layout optimization using the genetic algorithm , 2000 .

[5]  C. R. Liu,et al.  Generation of workpiece orientations for machining using a rule-based system , 1988 .

[6]  Warren R. DeVries,et al.  Optimization Methods Applied to Selecting Support Positions in Fixture Design , 1991 .

[7]  K F Gill,et al.  Knowledge Representation Database for the Development of a Fixture Design Expert System , 1988 .

[8]  Shreyes N. Melkote,et al.  Optimal Fixture Design Accounting for the Effect of Workpiece Dynamics , 2001 .

[9]  Andrew Y. C. Nee,et al.  Applying AI in jigs and fixtures design , 1987 .

[10]  Amy J. C. Trappey,et al.  Automated fixture configuration using projective geometry approach , 1993 .

[11]  Shabbir Choudhuri,et al.  An investigation of the effectiveness of fixture layout optimization methods , 2002 .

[12]  Andrew Y. C. Nee,et al.  Expert fixture-design system for an automated manufacturing environment , 1992, Comput. Aided Des..

[13]  Edward C. De Meter,et al.  Fast support layout optimization , 1998 .

[14]  Stelios Kafandaris,et al.  Expert Process Planning for Manufacturing , 1990 .

[15]  Jonathan W. Lee,et al.  Finite-Element Analysis of Flexible Fixturing System , 1987 .

[16]  Joseph J. Rencis,et al.  Development of a Finite Element Analysis Tool for Fixture Design Integrity Verification and Optimization , 2002 .

[17]  Yiming Rong,et al.  Automated modular fixture planning: Geometric analysis , 1998 .

[18]  Brian S. Thompson,et al.  Automated design of modular fixtures for flexible manufacturing systems , 1986 .

[19]  Cheng-liang Liu.  A systematic conceptual design of modular fixtures , 1994 .

[20]  Zsuzsanna Markusz,et al.  Fixture de-sign using prolog: An expert system , 1984 .

[21]  H.J.J. Kals,et al.  FIXES, a system for automatic selection of set-ups and design of fixtures , 1988 .