Steel–Concrete–Steel sandwich slabs with lightweight core — Static performance

Abstract This paper investigates the static performance of Steel–Concrete–Steel (SCS) sandwich slabs which consist of an ultra-lightweight concrete core sandwiched between two steel plates. Special J-hook connectors have been developed to develop composite action between the concrete core and the two steel plates. The core is made of lightweight concrete of density less than 1450 kg/m 3 . Laboratory tests were carried out on eight SCS sandwich slabs under centrally applied patch load. Test results showed that the mode of failure and crack pattern of SCS sandwich slabs were very similar to those of reinforced concrete slabs especially when the concrete core and steel plates act in a fully composite manner. Flexural and punching are the primary modes of failure. After flexural yielding, membrane action developed in the slab due to the effectiveness of J-hook connectors in maintaining composite action which further increases its load carrying capacity after flexural yielding. Theoretical models are proposed to predict the flexural and punching resistance and a good correlation with test results is obtained. A large deflection analysis considering plate membrane action is also proposed to predict the force deflection relation of SCS sandwich slabs.

[1]  Nemkumar Banthia,et al.  SHEAR STRENGTH OF STEEL FIBER-REINFORCED CONCRETE , 2002 .

[2]  Comite Euro-International du Beton,et al.  CEB-FIP Model Code 1990 , 1993 .

[3]  J. Y. Richard Liew,et al.  Experimental investigation of low-velocity impact characteristics of steel-concrete-steel sandwich beams , 2003 .

[4]  G. Wang,et al.  A Simple Method for Predicting the Grounding Strength of Ships , 1997 .

[5]  A. R. Cusens,et al.  FLEXURAL TESTS OF STEEL-CONCRETE-STEEL SANDWICHES , 1976 .

[6]  R. Taylor.  A note on a possible basis for a new method of ultimate load design of reinforced concrete slabs , 1965 .

[7]  N. Malek,et al.  Steel-Concrete Sandwich Members Without Shear Reinforcement , 1993 .

[8]  Nemkumar Banthia,et al.  Shear strength of reinforced concrete beams with a fiber concrete matrix , 2006 .

[9]  Ian Burgess,et al.  Experimental behaviour of concrete floor slabs at large displacements , 2004 .

[10]  Gib Rankin,et al.  PREDICTING THE PUNCHING STRENGTH OF CONVENTIONAL SLAB-COLUMN SPECIMENS. , 1987 .

[11]  William Zuk.  PREFABRICATED SANDWICH PANELS FOR BRIDGE DECKS , 1974 .

[12]  Nutan Kumar Subedi,et al.  Improving the strength of fully composite steel-concrete-steel beam elements by increased surface roughness—an experimental study , 2002 .

[13]  Chan Ghee Koh,et al.  Impact tests on steel–concrete–steel sandwich beams with lightweight concrete core , 2009 .

[14]  Colin Bailey,et al.  Membrane action of unrestrained lightly reinforced concrete slabs at large displacements , 2001 .

[15]  A W Beeby,et al.  CONCISE EUROCODE FOR THE DESIGN OF CONCRETE BUILDINGS. BASED ON BSI PUBLICATION DD ENV 1992-1-1: 1992. EUROCODE 2: DESIGN OF CONCRETE STRUCTURES. PART 1: GENERAL RULES AND RULES FOR BUILDINGS , 1993 .

[16]  N. E. Shanmugam,et al.  Finite element modelling of double skin composite slabs , 2002 .

[17]  K. F. Chung,et al.  Composite column design to Eurocode 4 : based on DD ENV 1994-1-1: 1994 Eurocode 4: design of composite steel and concrete structures: part 1.1: general rules and rules for buildings , 1994 .

[18]  J. Y. Richard Liew,et al.  Structural Performance of Steel-Concrete-Steel Sandwich Composite Structures , 2010 .

[19]  J. Y. Richard Liew,et al.  Lightweight steel-concrete-steel sandwich system with J-hook connectors , 2009 .

[20]  T. Oduyemi,et al.  An experimental investigation into the behaviour of double-skin sandwich beams , 1989 .