Topology optimization in concrete construction: a systematic review on numerical and experimental investigations

Structural optimization within concrete construction has been increasingly taken up in research within the last two decades. Possible drivers are the need for material-reduced and thus resource-efficient structures as well as recent advancements in automated concrete construction. However, structural concrete is characterized by nonlinear material behavior. Consequently, the merge of structural concrete design and topology optimization is not trivial. This paper reviews and assesses the topic of topology optimization within concrete construction, carrying out an extensive quantitative as well as qualitative review on practical and numerical applications. The following research areas are identified: Multimaterial modeling, stress constraints, concrete damage modeling, strut and tie modeling, combined truss-continuum topology optimization, the consideration of multiple load cases, a focus on construction techniques and alternative approaches. Although the number of research papers dealing with the topic of topology optimization in concrete construction is numerous, there are only few that actually realized topology optimized concrete structures. In addition, only a little number of experiments was performed for an objective evaluation of the found geometries so far. Concluding this review, a list of future challenges, like the incorporation of sustainability measurements within the optimization process, is given and thus serves as a guidance for subsequent research.

[1]  Anders Clausen,et al.  Efficient topology optimization in MATLAB using 88 lines of code , 2011 .

[2]  L. Valdevit,et al.  Incorporating fabrication cost into topology optimization of discrete structures and lattices , 2015 .

[3]  C. D. Wolf,et al.  A sustainable future for the European Cement and Concrete Industry: Technology assessment for full decarbonisation of the industry by 2050 , 2018 .

[4]  Gieljan Vantyghem,et al.  3D printing of a post-tensioned concrete girder designed by topology optimization , 2020 .

[5]  Karl Culmann,et al.  Die graphische Statik , 2014 .

[6]  Andrei Jipa,et al.  3D-Printed Stay-in-Place Formwork for Topologically Optimized Concrete Slabs , 2016 .

[7]  Gieljan Vantyghem,et al.  Density-based topology optimization for 3D-printable building structures , 2019, Structural and Multidisciplinary Optimization.

[8]  Matteo Bruggi,et al.  A stress–based approach to the optimal design of structures with unilateral behavior of material or supports , 2013 .

[9]  Asbjørn Søndergaard,et al.  Realization of Topology Optimized Concrete Structures Using Robotic Abrasive Wire-Cutting of Expanded Polystyrene Formwork , 2018 .

[10]  Matteo Bruggi,et al.  A numerical method to generate optimal load paths in plain and reinforced concrete structures , 2016 .

[11]  Asbjørn Søndergaard,et al.  Three-dimensional topology optimisation in architectural and structural design of concrete structures , 2010 .

[12]  Peter Mark,et al.  Experimental analyses of an optimized shear load transfer in the circumferential joints of concrete segmental linings , 2015 .

[13]  Robbie M. Andrew,et al.  Supplementary material to "Global CO2 Emissions from Cement Production" , 2017 .

[14]  Ole Sigmund,et al.  Closing the gap towards super-long suspension bridges using computational morphogenesis , 2020, Nature Communications.

[15]  J Schlaich,et al.  TOWARD A CONSISTENT DESIGN OF STRUCTURAL CONCRETE , 1987 .

[16]  Matthew Gilbert,et al.  Rationalization of trusses generated via layout optimization , 2015 .

[17]  H. Baier,et al.  Optimierung in der Strukturmechanik , 1994 .

[18]  Harianto Hardjasaputra Evolutionary Structural Optimization as Tool in Finding Strut-and-tie-models for Designing Reinforced Concrete Deep Beam , 2015 .

[19]  Andrew Liew,et al.  Design, fabrication and testing of a prototype, thin-vaulted, unreinforced concrete floor , 2017 .

[20]  Kun Cai,et al.  A simple approach to find optimal topology of a continuum with tension-only or compression-only material , 2011 .

[21]  Andrei Jipa,et al.  3D-printed formwork for bespoke concrete stairs: from computational design to digital fabrication , 2019, SCF.

[22]  Jack Chin Pang Cheng,et al.  Reinforced concrete structural design optimization: A critical review , 2020 .

[23]  Oded Amir,et al.  A topology optimization procedure for reinforced concrete structures , 2013 .

[24]  D. C. Drucker,et al.  Soil mechanics and plastic analysis or limit design , 1952 .

[25]  Osvaldo M. Querin,et al.  Generation of strut-and-tie models by topology design using different material properties in tension and compression , 2011 .

[26]  P. Duysinx,et al.  Topology optimization for minimum weight with compliance and stress constraints , 2012 .

[27]  Oded Amir,et al.  Topology optimization and digital assembly of advanced space-frame structures , 2013 .

[28]  Martina Schnellenbach-Held,et al.  Bionic Optimization of Concrete Structures by Evolutionary Algorithms , 2014 .

[29]  Julián A. Norato,et al.  Stress-based topology optimization for continua , 2010 .

[30]  Ole Sigmund,et al.  Reinforcement layout design for concrete structures based on continuum damage and truss topology optimization , 2013 .

[31]  James K. Guest,et al.  Reinforced Concrete Force Visualization and Design Using Bilinear Truss-Continuum Topology Optimization , 2013 .

[32]  Yi Min Xie,et al.  Topology Optimization of Strut-and-Tie Models in Reinforced Concrete Structures Using an Evolutionary Procedure , 2000 .

[33]  Glaucio H. Paulino,et al.  Connecting architecture and engineering through structural topology optimization , 2014 .

[34]  Hyo-Gyoung Kwak,et al.  Determination of Strut-and-Tie Models using Evolutionary Structural Optimization , 2002 .

[35]  Osvaldo M. Querin,et al.  Topology optimization of truss-like continua with different material properties in tension and compression , 2010 .

[36]  Zhan Kang,et al.  Layout design of reinforced concrete structures using two-material topology optimization with Drucker–Prager yield constraints , 2013 .

[37]  Hernán Santa María,et al.  Experimental evaluation of optimized strut‐and‐tie models for a dapped beam , 2016 .

[38]  Oded Amir,et al.  Topology optimization for additive manufacturing: Accounting for overhang limitations using a virtual skeleton , 2017 .

[39]  Harvey J. Greenberg,et al.  Automatic design of optimal structures , 1964 .

[40]  Domenico Asprone,et al.  Topology optimization of stress-constrained structural elements using risk-factor approach , 2019, Computers & Structures.

[41]  Oded Amir,et al.  Stress-constrained continuum topology optimization: a new approach based on elasto-plasticity , 2016, ArXiv.

[42]  Rafael H. Lopez,et al.  Design complexity control in truss optimization , 2016 .

[43]  P. Mark,et al.  Multi-level Optimisation of Parabolic Shells with Stiffeners Made from High-Performance Concrete , 2018 .

[44]  Johann Kollegger,et al.  fib Bulletin 45. Practitioners’ guide to finite element modelling of reinforced concrete structures , 2008 .

[45]  Matteo Bruggi,et al.  Generating strut-and-tie patterns for reinforced concrete structures using topology optimization , 2009 .

[46]  Oded Amir,et al.  Topology optimization for staged construction , 2018 .

[47]  Freek Bos,et al.  Optimising 3D printed concrete structures using topology optimisation , 2017 .

[48]  O. Amir,et al.  Conceptual design of reinforced concrete structures using topology optimization with elastoplastic material modeling , 2012 .

[49]  Michael Yu Wang,et al.  Optimal topology design of steel-concrete composite structures under stiffness and strength constraints , 2012 .

[50]  Matteo Bruggi,et al.  On the Automatic Generation of Strut and Tie Patterns under Multiple Load Cases with Application to the Aseismic Design of Concrete Structures , 2010 .

[51]  Yi Min Xie,et al.  Topology optimization of strut-and-tie models in non-flexural reinforced concrete members , 1999 .

[52]  Odysseas Kontovourkis,et al.  Robotic additive manufacturing (RAM) with clay using topology optimization principles for toolpath planning: the example of a building element , 2020, Architectural Science Review.

[53]  Martina Schnellenbach-Held,et al.  Bionic Structures for Innovative Concrete Slabs , 2015 .

[54]  Prabhat Kumar Optimal force transmission in reinforced concrete deep beams , 1978 .

[55]  Ren-Jye Yang,et al.  Stress-based topology optimization , 1996 .

[56]  Osvaldo M. Querin,et al.  Topology Design Methods for Structural Optimization , 2017 .

[57]  Gieljan Vantyghem,et al.  Compliance, Stress-Based and Multi-physics Topology Optimization for 3D-Printed Concrete Structures , 2018, RILEM Bookseries.

[58]  Klaus Hackl,et al.  A variational growth approach to topology optimization , 2015 .

[59]  Y. Xie,et al.  3D and multiple load case bi-directional evolutionary structural optimization (BESO) , 1999 .

[60]  Charlie C. L. Wang,et al.  Space-time topology optimization for additive manufacturing , 2019, Structural and Multidisciplinary Optimization.

[61]  M. Zając,et al.  Development of composite cements characterized by low environmental footprint , 2019, Journal of Cleaner Production.

[62]  Mark Alexander Ahrens,et al.  Toward holistic tension- or compression-biased structural designs using topology optimization , 2019, Engineering Structures.

[63]  Luc Taerwe,et al.  fib model code for concrete structures 2010 , 2013 .

[64]  Ole Sigmund,et al.  A 99 line topology optimization code written in Matlab , 2001 .

[65]  P. Mark,et al.  Experimental analysis of concrete elements under partial area strip loading , 2019, Civil Engineering Design.

[66]  Matteo Bruggi,et al.  Finite element analysis of no–tension structures as a topology optimization problem , 2014 .

[67]  Yi Min Xie,et al.  Evolutionary Topology Optimization of Continuum Structures: Methods and Applications , 2010 .

[68]  J. Petersson,et al.  Numerical instabilities in topology optimization: A survey on procedures dealing with checkerboards, mesh-dependencies and local minima , 1998 .

[69]  Shutian Liu,et al.  Topology optimization of continuum structures with different tensile and compressive properties in bridge layout design , 2011 .

[70]  Ekkehard Ramm,et al.  Optimization of fiber geometry for fiber reinforced composites considering damage , 2010 .

[71]  Y. Xie,et al.  A simple evolutionary procedure for structural optimization , 1993 .

[72]  Johann Kollegger,et al.  Building lightweight structures with carbon‐fiber‐reinforced polymer‐reinforced ultra‐high‐performance concrete: Research approach, construction materials, and conceptual design of three building components , 2018, Structural Concrete.

[73]  A. Michell LVIII. The limits of economy of material in frame-structures , 1904 .

[74]  M. Bendsøe Optimal shape design as a material distribution problem , 1989 .

[75]  Philippe Block,et al.  THRUST NETWORK ANALYSIS : A NEW METHODOLOGY FOR THREE-DIMENSIONAL EQUILIBRIUM , 2007 .

[76]  Grégoire Allaire,et al.  Structural optimization under overhang constraints imposed by additive manufacturing technologies , 2017, J. Comput. Phys..

[77]  H. A. Kim,et al.  An evaluative study on ESO and SIMP for optimising a cantilever tie—beam , 2007 .

[78]  Benjamin Kromoser Ressourceneffizientes Bauen mit Betonfertigteilen Material – Struktur – Herstellung , 2021 .

[79]  Mu Zhu,et al.  Considering Constructability in Structural Topology Optimization , 2014 .

[80]  Peter Mark,et al.  Hybrid reinforcement design of longitudinal joints for segmental concrete linings , 2019 .

[81]  M. A. Ahrens,et al.  Optimised High-Performance Concrete Shells for Parabolic Trough Collectors , 2017 .

[82]  Wolfgang Achtziger Truss topology optimization including bar properties different for tension and compression , 1996 .

[83]  Matthijs Langelaar,et al.  An additive manufacturing filter for topology optimization of print-ready designs , 2016, Structural and Multidisciplinary Optimization.

[84]  Boyan Stefanov Lazarov,et al.  Topology optimization using PETSc: An easy-to-use, fully parallel, open source topology optimization framework , 2015 .

[85]  Gieljan Vantyghem,et al.  Multi-physics topology optimization for 3D-printed structures , 2018 .

[86]  Liang-Jenq Leu,et al.  Strut-and-Tie Design Methodology for Three-Dimensional Reinforced Concrete Structures , 2006 .

[87]  M. Bendsøe,et al.  Topology optimization of continuum structures with local stress constraints , 1998 .

[88]  Z. Kang,et al.  Topology optimization of continuum structures with Drucker-Prager yield stress constraints , 2012 .

[89]  Robbie M. Andrew,et al.  Global CO2 emissions from cement production, 1928–2018 , 2018, Earth System Science Data.

[90]  M. Bendsøe,et al.  Generating optimal topologies in structural design using a homogenization method , 1988 .

[91]  James K. Guest,et al.  Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design , 2016 .

[92]  Matteo Bruggi,et al.  Topology optimization of the fiber-reinforcement retrofitting existing structures , 2013 .

[93]  Michael Yu Wang,et al.  Topology optimization of reinforced concrete structures considering control of shrinkage and strength failure , 2015 .

[94]  Josephine V. Carstensen,et al.  Topology-optimized design, construction and experimental evaluation of concrete beams , 2019, Automation in Construction.

[95]  Georgios Gaganelis,et al.  Tension/compression anisotropy enhanced topology design , 2019, Structural and Multidisciplinary Optimization.

[96]  Behrooz Hassani,et al.  Simultaneous shape and topology optimization of shell structures , 2013, Structural and Multidisciplinary Optimization.

[97]  Axel Schumacher,et al.  Optimierung mechanischer Strukturen , 2013 .

[98]  K. Svanberg The method of moving asymptotes—a new method for structural optimization , 1987 .

[99]  Georgios Gaganelis,et al.  Downsizing weight while upsizing efficiency: An experimental approach to develop optimized ultra‐light UHPC hybrid beams , 2019, Structural Concrete.

[100]  Ekkehard Ramm,et al.  Multiphase material optimization for fiber reinforced composites with strain softening , 2009 .

[101]  Nikos D. Lagaros,et al.  Conceptual design of structural systems based on topology optimization and prefabricated components , 2020 .

[102]  Fachwerkmodellbildung mit topologischen Optimierungsverfahren , 2014 .

[103]  James K. Guest,et al.  Reinforced Concrete Design with Topology Optimization , 2010 .

[104]  Marcelo Greco,et al.  Strut-and-tie models for linear and nonlinear behavior of concrete based on topological evolutionary structure optimization (ESO) , 2019, Revista IBRACON de Estruturas e Materiais.

[105]  Satoshi Murata,et al.  Application of 3D Printed Segments Designed by Topology Optimization Analysis to a Practical Scale Prestressed Pedestrian Bridge , 2020 .

[106]  Oded Amir,et al.  Simultaneous shape and topology optimization of prestressed concrete beams , 2017, Structural and Multidisciplinary Optimization.

[107]  Ole Sigmund,et al.  Extensions and applications , 2004 .

[108]  Max A.N. Hendriks,et al.  Optimization‐based three‐dimensional strut‐and‐tie model generation for reinforced concrete , 2020, Comput. Aided Civ. Infrastructure Eng..

[109]  Erik Holmberg,et al.  Stress constrained topology optimization , 2013, Structural and Multidisciplinary Optimization.

[110]  Rhj Ron Peerlings,et al.  Gradient enhanced damage for quasi-brittle materials , 1996 .

[111]  Domenico Asprone,et al.  Combining Multiple Loads in a Topology Optimization Framework for Digitally Fabricated Concrete Structures , 2020 .

[112]  Federico Ferrari,et al.  A new generation 99 line Matlab code for compliance topology optimization and its extension to 3D , 2020, ArXiv.

[113]  Benjamin Kromoser,et al.  Cradle-to-gate life cycle assessment of CFRP reinforcement for concrete structures: Calculation basis and exemplary application , 2021 .

[114]  G. Allaire,et al.  Geometric constraints for shape and topology optimization in architectural design , 2017 .

[115]  F. Navarrina,et al.  Topology optimization of continuum structures with local and global stress constraints , 2009 .

[116]  Yi Xia,et al.  A critical evaluation of topology optimization results for strut‐and‐tie modeling of reinforced concrete , 2020, Comput. Aided Civ. Infrastructure Eng..

[117]  Domenico Raffaele,et al.  Designing Simply Supported R.C. Bridge Decks Subjected to In-Plane Actions: Strut-and-Tie Model Approach , 2012 .