Measurement of thermal expansion coefficients using an in-fibre Bragg-grating sensor

A simple method to measure the thermal expansion coefficient using a surface-mounted Bragg-grating sensor is presented. This method uses a single, uniform-pitch Bragg-grating fibre that is only partially glued onto the specimen. To prevent cross talk between the two Bragg wavelengths reflecting from glued and free sections, a preloading is applied to the fibre before it is partially glued onto the specimen. After release, two Bragg wavelengths are observed. The Bragg wavelength reflected from the sensor section not glued onto the specimen is used to measure temperature variations; the Bragg wavelength reflected from the sensor section glued onto the specimen is affected by variations in thermal strain. Therefore, the thermal expansion coefficient can be determined by calculating the spectral separation of the two Bragg wavelengths. The measured thermal expansion coefficient of an aluminium plate is for every C in the range 35-C. It is in good agreement with the value of for aluminium. However, the scheme will lead to incorrect results if there is a temperature gradient across the Bragg grating or if the material to be measured is inhomogeneous.

[1]  D. Hashinger,et al.  Thermal expansion and filler content of composite resins. , 1984, The Journal of prosthetic dentistry.

[2]  Yu-Lung Lo,et al.  USING IN-FIBER BRAGG-GRATING SENSORS FOR MEASURING AXIAL STRAIN AND TEMPERATURE SIMULTANEOUSLY ON SURFACES OF STRUCTURES , 1998 .

[3]  Hideyuki Kato,et al.  Measurements of linear thermal expansion coefficients of copper SRM 736 and some commercially available coppers in the temperature range 20–300 K by means of an absolute interferometric dilatometer , 1997 .

[4]  James S. Sirkis,et al.  Optical fiber sensor for simultaneous measurement of strain and temperature , 1997, Smart Structures.

[5]  K. Hill,et al.  Photosensitivity in optical fiber waveguides: Application to reflection filter fabrication , 1978 .

[6]  James S. Sirkis,et al.  Simple method to measure temperature and axial strain simultaneously using one in-fiber Bragg grating sensor , 1997, Smart Structures.

[7]  J. Sirkis.  Unified approach to phase-strain-temperature models for smart structure interferometric optical fiber sensors: part 1, development , 1993 .

[8]  Brian Culshaw,et al.  Fiber optic technique for simultaneous measurement of strain and temperature variations in composite materials , 1991, Other Conferences.

[9]  J Ma,et al.  Optical-fiber sensor for simultaneous measurement of pressure and temperature: analysis of cross sensitivity. , 1996, Applied optics.

[10]  J. S. Sirkis,et al.  Simultaneous Measurement of Strain and Temperature Using Optical Fiber Sensors: Two Novel Configuration , 1996 .

[11]  A. Versluis,et al.  Thermal expansion coefficient of dental composites measured with strain gauges. , 1996, Dental materials : official publication of the Academy of Dental Materials.

[12]  Raymond M. Measures,et al.  Characteristics of fiber grating sensors and their relation to manufacturing techniques , 1995, Smart Structures.

[13]  G. Scherer.  Use of a Bimaterial Strip to Predict Expansion Compatibility , 1987, Journal of dental research.

[14]  John P. Dakin,et al.  Discrimination between strain and temperature effects using dual-wavelength fibre grating sensors , 1994 .

[15]  Richard O. Claus,et al.  Fiber optic sensor for simultaneous measurement of strain and temperature , 1991, Other Conferences.

[16]  D. Post,et al.  Moiré interferometry for thermal expansion of composites , 1981 .

[17]  J. Powers,et al.  Thermal Expansion of Composite Resins and Sealants , 1979, Journal of dental research.

[18]  J Jarzynski,et al.  Temperature-induced optical phase shifts in fibers. , 1981, Applied optics.

[19]  E. Neumann.  Single-mode fibers , 1988 .