Analysis of the fractal dimension of grain boundaries of AA7050 aluminum alloys and its relationship to fracture toughness

Quantitative analysis of the grain boundaries in partially recrystallized microstructures of heat-treated 7050 aluminum alloys has been performed. Fractal dimensions of the extracted grain boundaries were calculated by box-counting method. Five different types of tear-tested materials rolled in different processes each at two orientations of 0° and 90° were studied. Efforts were made to connect the fractal dimensions of grain boundaries in the crack propagation direction to the fracture toughness (unit propagation energy, UPE, in tear test). The results show that there is a linear correlation between UPE and the fractal dimensions of the grain boundaries along the crack propagation direction for both 0° and 90° samples. The dependence corresponds well with the observation of transition from intergranular fracture to transgranular fracture with the increase of UPE. Quantitative analysis has also been performed on the micrographs to estimate the degree of recrystallization and the grain size in crack growth direction. No correlation between the fraction of recrystallized grains and the UPE could be detected.

[1]  Manabu Tanaka,et al.  Characterization of Grain Boundaries by Fractal Geometry and Creep-Rupture Properties of Heat-Resistant Alloys / Charakterisierung von Korngrenzen nach Konzepten fraktaler Geometrie und die Kriecheigenschaften warmfester Legierungen , 1991 .

[2]  J. Planès,et al.  Fractal Dimension of Fractured Surfaces: A Universal Value? , 1990 .

[3]  Arun M. Gokhale,et al.  Relationship between fracture toughness, fracture path, and microstructure of 7050 aluminum alloy: Part I. Quantitative characterization , 1998 .

[4]  Hideki Takayasu,et al.  Fractals in the Physical Sciences , 1990 .

[5]  Liang Yu,et al.  Three-dimensional fractal analysis of fracture surfaces in titanium–iron particulate reinforced hydroxyapatite composites: relationship between fracture toughness and fractal dimension , 2011 .

[6]  A. Deschamps,et al.  Grain boundary versus transgranular ductile failure , 2003 .

[7]  J. T. Staley,et al.  Application of modern aluminum alloys to aircraft , 1996 .

[8]  D. Yoon,et al.  The dendritic growth of γ′ precipitates and grain , 1993, Metallurgical and Materials Transactions A.

[9]  Manabu Tanaka,et al.  Effects of the creep deformation on the fractal dimension of the grain boundaries in an austenite steel , 1998 .

[10]  Xinran Xiao,et al.  An approach on the mode-I fracture toughness anisotropy for materials with layered microstructures , 1995 .

[11]  S. Tsurekawa,et al.  The control of brittleness and development of desirable mechanical properties in polycrystalline systems by grain boundary engineering , 1999 .

[12]  W. Monteiro,et al.  The effect of microstructure on the mechanical behavior and fracture mechanism in a 7050-T76 aluminum alloy , 1991 .

[13]  B. Ralph,et al.  Kinetics of grain growth in powder-formed IN-792: A nickel-base superalloy , 1990 .

[14]  M. Rakin,et al.  Microstructural dependence of fracture toughness in high-strength 7000 forging alloys , 2008 .

[15]  S. Tsurekawa,et al.  Toughening of brittle materials by grain boundary engineering , 2004 .

[16]  Fractal dimension measured with perimeter-area relation and toughness of materials. , 1988, Physical review. B, Condensed matter.

[17]  A. Vasudévan,et al.  Grain boundary ductile fracture in precipitation hardened aluminum alloys , 1987 .

[18]  J. Knott,et al.  The influence of compositional and microstructural variations on the mechanism of static fracture in aluminum alloys , 1978 .

[19]  Subra Suresh,et al.  Crack deflection: Implications for the growth of long and short fatigue cracks , 1983 .

[20]  H. Iizuka,et al.  Creep rupture strength and grain-boundary sliding in austenitic 21 Cr-4Ni-9Mn steels with serrated grain boundaries , 1988 .

[21]  E. Hornbogen,et al.  The mechanism of pseudo-intercrystalline brittleness of precipitation-hardened alloys and tempered steels , 1982 .

[22]  P. Hähner,et al.  Fractal analysis of deformation-induced dislocation patterns , 1999 .

[23]  H. Iizuka,et al.  Improvement of fatigue-crack growth resistance by grain-boundary reaction precipitates at high temperature , 1990 .

[24]  P. Hähner,et al.  Dislocation dynamics and work hardening of fractal dislocation cell structures , 1999 .

[25]  W. S. Miller,et al.  Recent development in aluminium alloys for aerospace applications , 2000 .

[26]  M. Yamazaki.  The Effect of Two-Step Solution Treatment on the Creep Rupture Properties of a High Carbon 18Cr-12Ni Stainless Steel , 1966 .

[27]  Y. Chou,et al.  Fractal characterization of the fracture surface of a high-strength low-alloy steel , 1998 .

[28]  P. Streitenberger,et al.  The effect of surface fractal dimension of particles on Ostwald ripening , 1991 .

[29]  Manabu Tanaka.  Characterization of grain-boundary configuration and fracture surface roughness by fractal geometry and creep-rupture properties of metallic materials , 1992 .

[30]  D. Wolf,et al.  Atomistic Concepts for Simulation of Grain Boundary Fracture , 1991 .

[31]  George Z. Voyiadjis,et al.  Grain Boundary Migration in Metals: Thermodynamics, Kinetics, Applications , 2000 .

[32]  N. Ryum.  The influence of a precipitate-free zone on the mechanical properties of an Al-Mg-Zn alloy , 1968 .

[33]  Ryoji Yuuki,et al.  Crack-morphological aspects in fracture mechanics , 1975 .

[34]  Wei Tang,et al.  Fractal characterization of impact fracture surface of steel , 2012 .

[35]  R. J. Mitchell,et al.  On the formation of serrated grain boundaries and fan type structures in an advanced polycrystalline nickel-base superalloy , 2009 .

[36]  Benoit B. Mandelbrot,et al.  Fractal Geometry of Nature , 1984 .

[37]  J. Rawers,et al.  Fractal analysis of caride morphology in high-Cr white cast irons , 1992 .

[38]  J. M. Larson,et al.  Metallurgical factors affecting the crack growth resistance of a superalloy , 1977 .

[39]  A. Deschamps,et al.  A model for predicting fracture mode and toughness in 7000 series aluminium alloys , 2004 .

[40]  M. Rakin,et al.  Micromechanical modelling of fracture toughness in overaged 7000 alloy forgings , 2006 .

[41]  Tadao Watanabe.  Grain boundary design and control for high temperature materials , 1993 .

[42]  Manabu Tanaka,et al.  ESTIMATION OF THE FRACTAL DIMENSION OF FRACTURE SURFACE PATTERNS BY BOX-COUNTING METHOD , 1999 .

[43]  A. K. Koul,et al.  On the mechanism of serrated grain boundary formation in Ni-based superalloys , 1983 .

[44]  Rafael Colás,et al.  On the variation of grain size and fractal dimension in an austenitic stainless steel , 2001 .

[45]  C. Lung,et al.  Fractal dimension of the fractured surface of materials , 1989 .

[46]  A. Gokhale,et al.  Relationship between fracture toughness, fracutre path, and microstructure of 7050 aluminum alloy: Part II. Multiple micromechanisms-based fracture toughness model , 1998 .

[47]  S. Nam,et al.  Investigation on the formation of serrated grain boundaries with grain boundary characteristics in an AISI 316 stainless steel , 2009 .

[48]  E. Hornbogen,et al.  Fractals in microstructure of metals , 1989 .

[49]  J. Beddoes,et al.  Influence of grain-boundary morphology on creep of a wrought Ni-base superalloy , 2009 .

[50]  Fractal nature and quantitative evaluation of microstructures in metallic materials , 1995, Journal of Materials Science.