A study of the cutting-induced heating effect on the machined surface in ultra-precision raster milling of 6061 Al alloy

In ultra-precision machining, the heating effect on a workpiece induced by cutting process itself plays an important role in the machining process as it affects tool life, machining accuracy, and the surface quality of the workpiece. This paper discusses the cutting-induced heating effect in ultra-precision raster milling based on the study of the time–temperature-dependent precipitation of 6061 aluminum alloy. Experiments are designed to estimate the temperature variation of the workpiece in ultra-precision machining by comparing the change in the size of precipitates in isothermal heat treatment with those in raster milling process under different depth of cut. Microscopical examination under a scanning electron microscope (SEM) revealed that the temperature on the raster-milled surface is much higher than 500°C. In the last part of this paper, the heat generation of the workpiece in the process of ultra-precision raster milling is simulated by finite element method, the result of which is found to be consistent with that from SEM.

[1]  Chi Fai Cheung,et al.  Modelling and simulation of freeform surface generation in ultra-precision raster milling , 2006 .

[2]  A. Crosky,et al.  Secondary precipitation in an Al–Mg–Si–Cu alloy , 2007 .

[3]  Chi Fai Cheung,et al.  Theoretical and experimental analysis of nano-surface generation in ultra-precision raster milling , 2008 .

[4]  T. Ueda,et al.  Temperature on Flank Face of Cutting Tool in High Speed Milling , 2001 .

[5]  M. Song.  Modeling the hardness and yield strength evolutions of aluminum alloy with rod/needle-shaped precipitates , 2007 .

[6]  E. Trent.  Chapter 5 – Heat in metal cutting , 2000 .

[7]  J. Hawk,et al.  Yield stress as determined from hardness measurements for mechanically alloyed aluminum base alloys , 1988 .

[8]  M. Couper,et al.  A TEM study of precipitation in Al-Mg-Si alloys , 2001 .

[9]  K. P. Maity,et al.  An experimental investigation of hot-machining to predict tool life , 2008 .

[10]  Mohammad Sheikh,et al.  An investigation of heat partition and tool wear in hard turning of H13 tool steel with CBN cutting tools , 2008 .

[11]  F. W. Taylor.  The Art of Cutting Metals , 1907 .

[12]  H. Degischer,et al.  Precipitation kinetics of Si in aluminium alloys , 2008 .

[13]  Suet To,et al.  Microstructural Changes at the Ultra-Precision Raster Milled Surface of Zn-Al Based Alloy , 2008 .

[14]  Steven Y. Liang,et al.  Modeling of cutting forces in near dry machining under tool wear effect , 2007 .

[15]  Xiangdong Ding,et al.  Modeling the strengthening response to aging process of heat-treatable aluminum alloys containing plate/disc- or rod/needle-shaped precipitates , 2003 .

[16]  A. Deschamps,et al.  Influence of predeformation on ageing in an Al–Zn–Mg alloy—I. Microstructure evolution and mechanical properties , 1998 .

[17]  Toshimichi Moriwaki,et al.  Effect of Cutting Heat on Machining Accuracy in Ultra-Precision Diamond Turning , 1990 .

[18]  Jehnming Lin,et al.  Inverse estimation of the tool-work interface temperature in end milling , 1995 .

[19]  Ian J. Polmear,et al.  Light Alloys: Metallurgy of the Light Metals , 1982 .

[20]  D. J. Richardson,et al.  Modelling of cutting induced workpiece temperatures for dry milling , 2006 .