Design and fabrication of stereolithography‐based aeroelastic wing models

Purpose – The purpose of this paper is to present a novel method to design and fabricate aeroelastic wing models for wind tunnel tests based on stereolithography (SL). This method can ensure the structural similarity of both external and internal structures between models and prototypes.Design/methodology/approach – An aluminum wing‐box was selected as the prototype, and its natural modes were studied by FEA and scaled down to obtain the desired dynamic behavior data. According to similarity laws, the structurally similar model was designed through a sequential design procedure of dimensional scaling, stiffness optimization and mass optimization. An SL model was then fabricated, and its actual natural modes was tested and compared with the desired data of the prototype.Findings – The first two natural frequencies of the model presented strong correlation with the desired data of the prototype. Both the external and internal structures of the model matched the prototype closely. The SL‐based method can sig...

[1]  Robert Beard,et al.  Evaluation of stereolithography rapid prototyping for low speed airfoil design , 1997 .

[2]  William Braisted,et al.  Evaluation of Rapid Prototyping Technologies for Use in Wind Tunnel Model Fabrication , 2005 .

[3]  Jonathan D. Bartley-Cho,et al.  Design and Analysis of HiLDA/AEI Aeroelastic Wind Tunnel Model , 2008 .

[4]  Mark French,et al.  Aeroelastic model design using parameter identification , 1996 .

[5]  Michimasa Fujino,et al.  Flutter Characteristics of an Over-the-Wing Engine Mount Business-Jet Configuration , 2003 .

[6]  A. Springer.  Evaluating Aerodynamic Characteristics of Wind-Tunnel Models Produced by Rapid Prototyping Methods , 1998 .

[7]  Charles Tyler,et al.  Development of a Low Cost, Rapid Prototype, Lambda Wing-Body Wind Tunnel Model , 2003 .

[8]  Ronald D. Ziemian,et al.  Shake‐table simulation study of small scale layered models , 2010 .

[9]  Vincent Thomson,et al.  A comparison of rapid prototyping techniques used for wind tunnel model fabrication , 1998 .

[10]  Zeng Dong.  Design of Low-Velocity Wing Tunnel Flutter Model of Aircraft Composite Structure , 2006 .

[11]  Philip V. Bayly,et al.  IMPACT TESTING OF STEREOLITHOGRAPHIC MODELS TO PREDICT NATURAL FREQUENCIES , 1999 .

[12]  Thomas Butler.  Model Design and Fabrication Improvements for Wind Tunnel Testing , 2005 .

[13]  Athanasios Dafnis,et al.  Dynamic qualification of the HIRENASD elastic wing model , 2009 .

[14]  Vasily V. Chedrik,et al.  Optimization Approach to Design of Aeroelastic Dynamically-Scaled Models of Aircraft , 2004 .

[15]  Andrew L. Heyes,et al.  Rapid Technique for Wind-Tunnel Model Manufacture , 2004 .

[16]  Carol D. Wieseman,et al.  Experimental Results from the Active Aeroelastic Wing Wind Tunnel Test Program , 2005 .

[17]  Li Shao.  PARTIAL STRUCTURE SIMILARITY METHOD TO DESIGN COMPOSITE TRANSONIC FLUTTER MODEL , 2009 .

[18]  S. Raja,et al.  Aeroelastic testing of aerospace vehicles - Experiences gained during four decades , 2009 .

[19]  Athanasios Dafnis,et al.  Dynamic aero-structural response of an elastic wing model , 2003 .

[20]  Jennifer Heeg,et al.  Wind Tunnel to Atmospheric Mapping for Static Aeroelastic Scaling , 2004 .

[21]  Zhihua Zhou,et al.  Design and fabrication of a hybrid surface‐pressure airfoil model based on rapid prototyping , 2008 .

[22]  Timothy M. Geipe.  Process Improvement for Aerodynamic Model Development , 2008 .