Uninterrupted and accelerated vibrational fatigue testing with simultaneous monitoring of the natural frequency and damping

Abstract A mechanical system's modal parameters change when fatigue loading is applied to the system. In order to perform an accelerated vibration-based fatigue test these changes must be taken into account in order to maintain constant-stress loading. This paper presents an improved accelerated fatigue-testing methodology based on the dynamic response of the test specimen to the harmonic excitation in the near-resonant area with simultaneous monitoring of the modal parameters. The measurements of the phase angle and the stress amplitude in the fatigue zone are used for the real-time adjustment of the excitation signal according to the changes in the specimen's modal parameters. The presented methodology ensures a constant load level throughout the fatigue process until the final failure occurs. With the proposed testing methodology it is possible to obtain a S-N point of the Woehler curve relatively quickly and to simultaneously monitor the changes of the specimen's natural frequency and damping loss factor. The presented methodology with real-time control is verified on an aluminum Y-shaped specimen (10 6 load cycles are achieved in 21 min) and is applicable to a specimen with arbitrary geometry. Besides the faster completion of the fatigue test the methodology can be adopted for the validation of the vibrational fatigue analysis.

[1]  Vincent Rouillard,et al.  A frequency domain technique for maintaining resonance condition during sine dwell vibration testing of packages , 2000 .

[2]  De-Guang Shang,et al.  Fatigue damage model based on the natural frequency changes for spot-welded joints , 2008 .

[3]  O. S. Salawu.  Detection of structural damage through changes in frequency: a review , 1997 .

[4]  Nicola Ivan Giannoccaro,et al.  Fatigue damage evaluation of notched specimens through resonance and anti-resonance data , 2006 .

[5]  M.-H. Herman Shen,et al.  Goodman Diagram Via Vibration-Based Fatigue Testing , 2005 .

[6]  P. M. Calderale,et al.  MEASUREMENT OF NON-LINEAR INTERNAL DAMPING IN METALS: PROCESSING OF DECAY SIGNALS IN A UNIAXIAL STRESS FIELD , 1996 .

[7]  R. M. French,et al.  A comparison of simultaneous and sequential single-axis durability testing , 2006 .

[8]  André Preumont,et al.  Spectral methods to estimate local multiaxial fatigue failure for structures undergoing random vibrations , 2001 .

[9]  Hongzhao Liu,et al.  Strain-dependent nonlinear damping and application to dynamic analysis of elastic linkage mechanism , 2005 .

[10]  Li Cheng,et al.  Development in vibration-based structural damage detection technique , 2007 .

[11]  Charles R. Farrar,et al.  Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review , 1996 .

[12]  Rafael Colás,et al.  Experimental investigation for fatigue strength of a cast aluminium alloy , 2011 .

[13]  P. Verboven,et al.  On-line detection of fatigue cracks using an automatic mode tracking technique , 2003 .

[14]  Dc Maxwell,et al.  Mean Stress Effects on the High Cycle Fatigue Limit Stress in Ti-6Al-4V , 2003 .

[15]  Carlo Rainieri,et al.  Near real-time tracking of dynamic properties for standalone structural health monitoring systems , 2011 .

[16]  John T. DeWolf,et al.  Experimental Study of Bridge Monitoring Technique , 1990 .

[17]  N. E. Bedewi,et al.  Effect of fatigue loading on the modal properties of composite structures and its utilization for prediction of residual life , 1997 .

[18]  Jwo Pan,et al.  Fatigue Testing and Analysis: Theory and Practice , 2004 .

[19]  J. Slavič,et al.  ENHANCEMENTS TO THE CONTINUOUS WAVELET TRANSFORM FOR DAMPING IDENTIFICATIONS ON SHORT SIGNALS , 2004 .

[20]  N. W. M. Bishop.  The use of frequency domain parameters to predict structural fatigue , 1988 .

[21]  J. Radziejewska,et al.  The fatigue damage development in a cast Al–Si–Cu alloy , 2011 .

[22]  E. Zanetti,et al.  Correlation between thermography and internal damping in metals , 2003 .

[23]  Jorge Daniel Riera,et al.  Damage detection by means of structural damping identification , 2008 .

[24]  K. L. Jerina,et al.  Material damping in 6061-T6511 aluminium to assess fatigue damage , 2003 .

[25]  D. J. Ewins,et al.  Modal Testing: Theory and Practice , 1984 .

[26]  Anil K. Chopra,et al.  Dynamics of Structures: Theory and Applications to Earthquake Engineering , 1995 .

[27]  Teik C. Lim,et al.  Effect of fatigue damage on the dynamic response frequency of spot-welded joints , 2003 .

[28]  S. Roy Swanson,et al.  Handbook of fatigue testing , 1974 .

[29]  Janko Slavič,et al.  Damping identification with the Morlet-wave , 2011 .

[30]  Jeremy D. Seidt,et al.  Development of a novel vibration-based fatigue testing methodology , 2004 .

[31]  Ruijie Wang,et al.  Fatigue life prediction based on natural frequency changes for spot welds under random loading , 2009 .

[32]  H. Gitano-Briggs,et al.  Design optimization and fatigue testing of an electronically-driven mechanically-resonant cantilever spring mechanism , 2010 .