JSR EUV Resist Development toward 22nmhp Design and Beyond

In order to achieve targeted resist performance for EUV in practical applications, we have developed new materials such as molecular glass (MG), PAG, and acid amplifiers (AA). Protected NORIA, a molecular glass, was examined for extending resolution limits. The resist with protected NORIA showed 22 nm hp resolutions under EUV exposure. PAG acid diffusion effect on LWR was also investigated. It was found that acid diffusion control was one of the most important factors for LWR improvement. To improve sensitivity, application of AA (acid amplifier) was investigated. The resist with AA gained 25% sensitivity improvement over the original formulation. Elemental technologies for major progress of EUV resist were made.

[1]  Hideaki Tsubaki,et al.  Resist material design to improve sensitivity in EUV lithography , 2009, Advanced Lithography.

[2]  Hyo-Jin Yun,et al.  Novel molecular resist based on derivative of cholic acid , 2002 .

[3]  Manish Chandhok,et al.  EUV lithography for 30nm half pitch and beyond: exploring resolution, sensitivity, and LWR tradeoffs , 2009, Advanced Lithography.

[4]  Mingxing Wang,et al.  Novel Ionic Photoacid Generators (PAGs) and Corresponding PAG Bound Polymers , 2007 .

[5]  Theodore H. Fedynyshyn,et al.  PAG segregation during exposure affecting innate material roughness , 2007, SPIE Advanced Lithography.

[6]  M. Ueda,et al.  A new positive-type photoresist based on mono-substituted hydroquinone calix[8]arene and diazonaphthoquinone , 1999 .

[7]  Y. Shirota.  Organic materials for electronic and optoelectronic devices , 2000 .

[8]  Synthesis, Characterization and Lithography Performance of Novel Anionic Photoacid Generator (PAG) Bound Polymers , 2007 .

[9]  Osamu Haba,et al.  Three-Component Negative-Type Photoresist Based on Calix[4]resorcinarene, a Cross-linker, and a Photoacid Generator , 1998 .

[10]  Seth Kruger,et al.  Kinetics, Chemical Modeling and Lithography of Novel Acid Amplifiers for Use in EUV Photoresists , 2009 .

[11]  S. Tagawa,et al.  Impact of Nonconstant Diffusion Coefficient on Latent Image Quality in 22 nm Fabrication using Extreme Ultraviolet Lithography , 2008 .

[12]  Yayi Wei,et al.  Evaluation of EUV resist materials for use at the 32 nm half-pitch node , 2008, SPIE Advanced Lithography.

[13]  Yoshikazu Yamaguchi,et al.  Influence of Acid Diffusion Length on Line Edge Roughness in KrF Photoresists , 2004 .

[14]  Iwao Nishiyama,et al.  Progress in EUV resist development , 2007 .

[15]  Brian Cardineau,et al.  Lithographic evaluation and chemical modeling of acid amplifiers used in EUV photoresists , 2009, Advanced Lithography.

[16]  Nelson Felix,et al.  Materials for future lithography (Invited Paper) , 2005, SPIE Advanced Lithography.

[17]  Hiroshi Kageyama,et al.  Creation of low-molecular-weight organic resists for nanometer lithography , 2001, SPIE Advanced Lithography.

[18]  Manish Chandhok,et al.  Improvement in linewidth roughness by postprocessing , 2008 .

[19]  Carlos Fonseca,et al.  EUV resist requirements: absorbance and acid yield , 2009, Advanced Lithography.

[20]  Shinji Matsui,et al.  Ultrahigh resolution of calixarene negative resist in electron beam lithography , 1996 .

[21]  Kouji Mitani,et al.  Molecular waterwheel (noria) from a simple condensation of resorcinol and an alkanedial. , 2006, Angewandte Chemie.

[22]  Sangwoong Yoon,et al.  Influence of activation energy on LER in chemically amplified KrF photoresists , 2004, SPIE Advanced Lithography.