In situ direct visualization of irradiated electron-beam patterns on unprocessed resists using atomic force microscopy

The authors introduce an in situ characterization method of resists used for electron-beam lithography. The technique is based on the application of an atomic force microscope, which is directly mounted below the cathode of an electron-beam lithography system. They demonstrate that patterns irradiated by the electron beam can be efficiently visualized and analyzed in surface topography directly after the electron-beam exposure. This in situ analysis takes place without any development or baking steps and gives access to the chemical (or latent) image of the irradiated resist.

[1]  F. Simmel,et al.  On-chip functionalization of carbon nanotubes with photosystem I. , 2010, Journal of the American Chemical Society.

[2]  L. Lagae,et al.  Enhanced resolution of poly(methyl methacrylate) electron resist by thermal processing , 2009, 1207.3183.

[3]  J. Kotthaus,et al.  Optoelectronic sensitization of carbon nanotubes by CdTe nanocrystals , 2008, 0807.2111.

[4]  Bryan M. Cord,et al.  Optimal temperature for development of poly(methylmethacrylate) , 2007 .

[5]  H. Namatsu,et al.  5-nm-Order Electron-Beam Lithography for Nanodevice Fabrication , 2003, Digest of Papers Microprocesses and Nanotechnology 2003. 2003 International Microprocesses and Nanotechnology Conference.

[6]  Weng Hong Teh,et al.  Cross-linked PMMA as a low-dimensional dielectric sacrificial layer , 2003 .

[7]  Richard Martel,et al.  Simple fabrication scheme for sub-10 nm electrode gaps using electron-beam lithography , 2002 .

[8]  Shazia Yasin,et al.  Fabrication of <5 nm width lines in poly(methylmethacrylate) resist using a water:isopropyl alcohol developer and ultrasonically-assisted development , 2001 .

[9]  Khaled Karrai,et al.  Interfacial shear force microscopy , 2000 .

[10]  Kenji Yamazaki,et al.  Influence of edge roughness in resist patterns on etched patterns , 1998 .

[11]  Axel Scherer,et al.  Fabrication of High-Density Nanostructures by Electron Beam Lithography , 1998 .

[12]  E. Snow,et al.  Atomic force microscope studies of nanolithographic exposure and development of polymethylmethacrylate , 1997 .

[13]  A. Broers,et al.  Electron beam lithography-Resolution limits , 1996 .

[14]  Leonidas E. Ocola,et al.  Scanning force microscopy measurements of latent image topography in chemically amplified resists , 1996 .

[15]  M. Nagase,et al.  An Electron Beam Nanolithography System and its Application to Si Nanofabrication , 1995 .

[16]  H. Marchman,et al.  Near field optical latent imaging with the photon tunneling microscope , 1995 .

[17]  Wei Chen,et al.  Fabrication of sub‐10 nm structures by lift‐off and by etching after electron‐beam exposure of poly(methylmethacrylate) resist on solid substrates , 1993 .

[18]  S. Chou,et al.  10 nm Si pillars fabricated using electron‐beam lithography, reactive ion etching, and HF etching , 1993 .

[19]  Wei Chen,et al.  Fabrication of 5–7 nm wide etched lines in silicon using 100 keV electron‐beam lithography and polymethylmethacrylate resist , 1993 .

[20]  B. Spangenberg,et al.  Nanostructure fabrication using lithium fluoride films as an electron beam resist , 1992 .

[21]  Robert R. Jackson,et al.  Latent image measurements in electron beam exposed polymethylmethacrylate , 1991 .

[22]  A. N. Broers,et al.  Resolution limits for electron-beam lithography , 1988 .

[23]  N. Samoto,et al.  Changes of Volume and Surface Compositions of Polymethylmethacrylate under Electron Beam Irradiation in Lithography , 1985 .

[24]  Harold G. Craighead,et al.  10‐nm resolution electron‐beam lithography , 1984 .

[25]  J. Greeneich.  Developer Characteristics of Poly‐(Methyl Methacrylate) Electron Resist , 1975 .

[26]  T. Van Duzer,et al.  Model for Exposure of Electron-Sensitive Resists , 1973 .