Digital Image Correlation of Strains at Profiled Wood Surfaces Exposed to Wetting and Drying

We hypothesize that machining grooves and ridges into the surface of radiata pine deck boards will change the pattern of strains that develop when profiled boards are exposed to wetting and drying. Two wavy profiles were tested, and flat unprofiled boards acted as controls. Full-field surface strain data was collected using digital image correlation. Strains varied across the surface of both flat and profiled boards during wetting and drying. Profiling fundamentally changed surface strain patterns; strain maxima and minima developed in the profile ridges and grooves during wetting, respectively, but this pattern of strains reversed during drying. Such a pronounced reversal of strains was not observed when flat boards were exposed to wetting and drying, although there was a shift towards negative strains when flat boards were dried. We conclude that profiling changes surface strain distribution in deck boards exposed to wetting and drying, and causes high strains to develop in the grooves of profiled boards. These findings help explain why checks in profiled deck boards are mainly confined to profile grooves where they are difficult to see, and the commercial success of profiling at reducing the negative effects of checking on the appearance of wood decking.

[1]  Audrey G. Zink,et al.  Strain measurement in wood using a digital image correlation technique , 1995 .

[2]  I. Cullis,et al.  Microstructure and Mechanism of Grain Raising in Wood , 2017 .

[3]  B. Meylan,et al.  The Influence of Microfibril Angle on Longitudinal and Tangential Shrinkage in Pinus radiata , 1965 .

[4]  Ulrich Müller,et al.  Measurement of strain distribution in timber finger joints , 2006, Wood Science and Technology.

[5]  P. Böttcher.  Einfluß verschiedenartiger Oberflächenprofilierungen an Holz auf die Veränderung der Wetterbeständigkeit , 1977, Holz als Roh- und Werkstoff.

[6]  S. J. Ghosh,et al.  Cracks in steam turbine components , 2006 .

[7]  Nick J. McCormick,et al.  Digital Image Correlation , 2010 .

[8]  P. Evans,et al.  Improving the Performance of Clear Coatings on Wood through the Aggregation of Marginal Gains , 2016 .

[9]  Michel Grédiac,et al.  The use of full-field measurement methods in composite material characterization: interest and limitations , 2004 .

[10]  M. Milota,et al.  Optical Measurement of Deformations in Drying Lumber , 2011 .

[11]  P. Evans,et al.  A note on the surface topography of profiled wood decking , 2016 .

[12]  D. Nicholas,et al.  Effect of profiling and preservative treatments on the weathering characteristics of Southern pine deck boards , 2014, European Journal of Wood and Wood Products.

[13]  W. Peters,et al.  Digital Imaging Techniques In Experimental Stress Analysis , 1982 .

[14]  P. Evans,et al.  Manufacture of Profiled Amabilis Fir Deckboards with Reduced Susceptibility to Surface Checking , 2018 .

[15]  P. Morris,et al.  Extracting greater value from subalpine fir: Profiled decking , 2009 .

[16]  M. Milota,et al.  Preliminary Tests for Optically Measuring Drying Strains and Check Formation in Wood , 2011 .

[17]  Sven Bossuyt,et al.  Quality assessment of speckle patterns for digital image correlation , 2006 .

[18]  Philip D. Evans,et al.  Automated measurement of checks at wood surfaces , 2005 .

[19]  R. Cunningham,et al.  Wax and oil emulsion additives: How effective are they at improving the performance of preservative-treated wood? , 2009 .

[20]  I. Cullis,et al.  Checking of Profiled Southern Pine and Pacific Silver Fir Deck Boards , 2010 .

[21]  D. Nicholas,et al.  Effect of machined profile, zinc oxide and titanium dioxide particles on checking southern pine deck boards during weathering. , 2015, IET nanobiotechnology.