Theoretical and experimental investigation of the filled-type evacuated tube solar collector with U tube

Abstract The filled-type evacuated tube with U-tube, in which the filled layer is used to transfer energy absorbed by the working fluid flowing in the U-tube, is proposed to eliminate the influence of thermal resistance between the absorber tube and the copper fin of the conventional evacuated solar collector. In this paper, the thermal performance of the filled-type evacuated tube with U-tube was researched by means of theoretical analysis and experimental study. The temperature of the working fluid in the flow direction was obtained, and the efficiency of the evacuated tube was also calculated, based on the energy balance equations for the working fluid in the U-tube. The effects of the heat loss coefficient and the thermal conductivity of the filled layer on the thermal performance of the evacuated tube were studied. In addition, the test setup of the thermal performance of the filled-type evacuated tube with U-tube was established. The evacuated tube considered in this study was a two-layered glass evacuated tube, and the absorber film was deposited in the outer surface of the absorber tube. The results show that the filled-type evacuated tube with U-tube has a favourable thermal performance. When the thermal conductivity of the heat transmission component is λ c  = 100, the efficiency of the filled-type evacuated tube with U-tube is 12% higher than that of the U-tube evacuated tube with a copper fin. The modelling predictions were validated using experimental data which show that there is a good concurrence between the measured and predicted results.

[1]  S. Rittidech,et al.  Experimental study of the performance of a circular tube solar collector with closed-loop oscillating heat-pipe with check valve (CLOHP/CV) , 2009 .

[2]  Ali A. Badran,et al.  On the measurement of bond conductance in solar collector absorber plate , 2008 .

[3]  Simon Furbo,et al.  Theoretical flow investigations of an all glass evacuated tubular collector , 2007 .

[4]  He Zinian,et al.  A comparison of optical performance between evacuated collector tubes with flat and semicylindric absorbers , 1997 .

[5]  E. Azad,et al.  Theoretical and experimental investigation of heat pipe solar collector , 2008 .

[6]  Stephen J. Kline,et al.  The Purposes of Uncertainty Analysis , 1985 .

[7]  Hyunjoo Han,et al.  A three-dimensional performance analysis of all-glass vacuum tubes with coaxial fluid conduit , 2008 .

[8]  Ruobing Liang,et al.  Thermal performance analysis of the glass evacuated tube solar collector with U-tube , 2010 .

[9]  Masud Behnia,et al.  Measurement and simulation of flow rate in a water-in-glass evacuated tube solar water heater , 2005 .

[10]  W. Beckman,et al.  Solar Engineering of Thermal Processes , 1985 .

[11]  Wongee Chun,et al.  The Performance Simulation of All-Glass Vacuum Tubes with Coaxial Fluid Conduit , 2007 .

[12]  Gerardo Diaz,et al.  Performance Analysis and Design Optimization of a Mini-Channel Evacuated-Tube Solar Collector , 2008 .

[13]  Graham L. Morrison,et al.  Performance of a Water-in-Glass Evacuated Tube Solar Water Heater , 2001 .

[14]  Yong Kim,et al.  Thermal performances comparisons of the glass evacuated tube solar collectors with shapes of absorber tube , 2007 .

[15]  N. K. Bansal,et al.  Performance Parameters of an Evacuated Tubular Collector With a U-Tube Fluid Channel , 1987 .

[16]  S. J. Kline,et al.  Describing Uncertainties in Single-Sample Experiments , 1953 .

[17]  E. Azad.  Performance analysis of wick-assisted heat pipe solar collector and comparison with experimental results , 2009 .

[18]  F. Rahman,et al.  Two-Dimensional Mathematical Model of Evacuated Tubular Solar Collector , 1984 .